Norav Medical NR-1207-E

Other manuals for Norav Medical NR-1207-E

Installation And Operation Guide20 pages

Questions and Answers

G
glawsonAug 14, 2025
What to do if I see a 'Lead OFF' message on Norav Medical Equipment?
- P
  Paula MorganAug 14, 2025
  If you're seeing a 'Lead OFF' message, make sure you've prepped the patient's skin according to instructions. Also, ensure the electrodes are properly applied and that the leads are making good contact with the electrodes. If the issue continues, try replacing the patient ECG cable.
A
Angelica BrownAug 17, 2025
Why am I getting noise artifacts on the ECG signal with my Norav Medical device?
- C
  courtneyleeAug 18, 2025
  Noise artifacts on the ECG signal can occur if the patient's skin isn't properly prepped, the electrodes aren't correctly applied, or the leads aren't making good contact. Ensure you've prepared the patient’s skin according to the instructions, the electrodes are properly applied to the patient, and the leads are making proper contact with the electrodes. Replacing the patient ECG cable can also help.
K
kevin44Aug 21, 2025
What to do if my Norav Medical Equipment displays 'Low battery' message?
- A
  Amy BuchananAug 21, 2025
  If you are getting a low battery message, install a new AA battery. Also, inspect the battery compartment and clean the contacts if necessary.
J
Jerry LeeAug 25, 2025
What to do if my Norav Medical Equipment is connected to the dock station but the NR device drive is not visible on the computer?
- J
  jennagarciaAug 25, 2025
  If the NR device drive isn't visible, use only a Norav USB cable, and try replacing it. Also, try connecting the USB cable to another USB port. Make sure the NR-314P is correctly connected to the dock station.
N
Nathaniel FernandezAug 27, 2025
How to fix 'SD Card Error' message on Norav Medical Equipment?
- R
  Robert RodriguezAug 28, 2025
  To resolve an SD Card Error, ensure the memory card is Norav Certified. Also, check that the memory card is not write-protected (look for a small switch on the SD Card). If problems persist, reformat the memory card or replace it with a new Norav certified memory card.
M
Michael PenaAug 31, 2025
What to do if my Norav Medical Equipment displays 'No Cable' message?
- A
  anna92Aug 31, 2025
  If you're seeing a 'No Cable' message, first ensure the patient cable (lead set) is connected to the NR device. Then, check that the connector on the NR device side isn't damaged, and inspect the cable connector pins for any breaks, bends, or damage.
D
Dr. Victoria PooleSep 3, 2025
Why won't my Norav Medical Equipment power on?
- R
  Regina JohnsonSep 3, 2025
  To resolve the issue of the NR device not powering on, ensure the battery is inserted with the correct polarity and install a new AA battery.
W
wjohnsonSep 6, 2025
What to do if my Norav Medical Equipment displays 'Previous recording found' message?
- D
  Danielle WrightSep 6, 2025
  If you see a 'Previous recording found' message, download the ECG data using the Computer Analysis System, or delete it from the SD card using the left and enter buttons.
W
Wanda PittsSep 10, 2025
What does 'Set Date/Time (message)' mean on my Norav Medical device, and how do I fix it?
- A
  Andrew BradleySep 12, 2025
  The 'Set Date/Time' message indicates that the internal battery that runs the real time clock may not be fully charged. Insert a fresh AA battery into the NR device and let the NR device charge for 12 hours.