NordicTrack NTEL7906.2 - Maintenance and Troubleshooting; How to Level the Elliptical Exerciser; How to Eliminate Flexing in the Center of the Elliptical Exerciser; How to Adjust the Belt

22
I
nspect and tighten all parts of the elliptical exerciser
regularly. Replace any worn parts immediately.
To clean the elliptical exerciser, use a damp cloth and
a
small amount of mild soap. IMPORTANT: To avoid
damage to the console, keep liquids away from
the console and keep the console out of direct
sunlight.
HOW TO LEVEL THE ELLIPTICAL EXERCISER
If the elliptical
exerciser rocks
on your floor dur-
ing use, turn one
or both of the
leveling feet
beneath the rear
stabilizer until the
rocking motion is
eliminated.
HANDGRIP PULSE SENSOR TROUBLESHOOTING
• Avoid moving your hands while using the handgrip
pulse sensor. Excessive movement may interfere
with heart rate readings.
• Do not hold the metal contacts too tightly; doing
so may interfere with heart rate readings.
• For the most accurate heart rate reading, hold the
metal contacts for about 30 seconds.
• For optimal performance of the handgrip pulse
sensor, keep the metal contacts clean. The con-
tacts can be cleaned with a soft cloth—never use
alcohol, abrasives, or chemicals to clean the
contacts.
H
OW TO ELIMINATE FLEXING IN THE CENTER OF
THE ELLIPTICAL EXERCISER
If the elliptical exerciser flexes in the center during
u
se, turn the center foot beneath the frame (see the
drawing at the left) until the flexing is eliminated.
HOW TO ADJUST THE BELT
If the pedals slip
while you are
pedaling, even
while the resis-
tance is adjusted
to the highest
setting, the belt
may need to be
adjusted. To
adjust the belt,
first carefully pry
off the left Disc
Cover (13) using a flat screwdriver. Next, remove the
four screws (not shown) from the center of the left
Disc (12). Gently rotate the Disc Cover and the Disc
away from the elliptical exerciser.
Loosen, but do
not remove, the
three 1/4" x
19mm Button
Screws (114).
Insert the shaft of
a screwdriver
downward
between the
Idler (47) and the
Idler Pulley (48).
Pull the top of the
screwdriver
toward the rear of the elliptical exerciser until the Belt
(96) is tight, and then tighten the three Button Screws.
Reattach the left disc with the four screws and then
reattach the left disc cover.
Leveling
Feet
Center
Foot
47
13
12
48
114
96
MAINTENANCE AND TROUBLESHOOTING
5. Insert the Roller (38) on the Left Pedal Arm (32)
and the Roller on the Right Pedal Arm (33) into
the sides of the Ramp (5).
Attach the Rear Ramp Cover (7) to the
Ramp (5) with two M4 x 16mm Screws (116).
See the inset drawing. Lift the Pedal Arm
Latch (41) on the Left Pedal Arm (32) and set
the end of the Left Pedal Arm on the left Crank
Bushing Sleeve (54). Release the Pedal Arm
Latch; make sure that the Left Pedal Arm is
securely connected to the Crank Bushing
Sleeve.
Connect the Right Pedal Arm (33) to the
right Crank Bushing Sleeve (not shown) in
the same way.
7
4. Identify the Left Pedal (34) and the Left Pedal
Arm (32), which are marked with stickers.
A
ttach the Left Pedal (34) to the Left Pedal
Arm (32) with two M6 x 62mm Screws (108),
t
wo M6 x 35mm Screws (109), and four M6
Split Washers (102).
Attach the Right Pedal (not shown) to the
Right Pedal Arm (not shown) in the same
way.
116
7
5
5
34
108
102
102
109
41
54
109
32
32
4
38
32
33
102