OPERATING INSTRUCTIONS
WARNING! BEFORE OPERATING THIS SYSTEM: Read all warnings at the beginning of this manual. If you do not
understand these operating instructions, contact Hyperice at +1.949.565.4994.
CHARGING THE SYSTEM
• Step 1: Plug the USB cable into the control unit
• Step 2: Plug the USB cable into the charger
• Step 3: Plug the USB charger into the wall outlet
• While the control unit is charging the battery status indicators will cycle from left to right. When all 5 battery
status indicators are on ON, this means that the system is fully charged.
The control unit will NOT power on and cannot be operated while the USB cable is connected.
Device is intended to be charged with the power adaptor provided. If you have any questions, please contact
Hyperice at +1.949.565.4994 or your local Customer Care Center or representative.
SET UP THE SYSTEM
• Step 1: Secure the wrap tightly around your calf. Affix the two sides of the hook and loop material together
for a snug but comfortable fit.
• Step 2: Press the power button on the Normatec Go control unit firmly for one second to turn on the
system. While the control unit is on, the battery LEDs and display screen will light up.
USING HYPERSYNC
™
Your Normatec Go devices arrive paired, which means they will inflate and deflate on the same cycle. To unpair devices, press
and hold the Start / Stop button on either device until the device screen reads “Unpaired!” and the white pairing indicator light
is no longer illuminated. To pair your devices, turn on both devices by pressing and holding the power (ON/OFF) button. Then
press and hold Start / Stop button on either control unit until the display screen says “Pairing!” Finally, press and hold the Start /
Stop button on the other device until both devices say “Pairing!” and the white pairing indicator light is illuminated.
CONNECT TO THE HYPERICE APP
Download the Hyperice App from the App Store or the Google Play Store. To connect your device to the Hyperice App
via Bluetooth® make sure that your device is turned on, Bluetooth® is turned on in your phone, and your device is within
range of your phone. The Bluetooth LED on the pod will pulse blue, which means it is waiting to pair. If prompted, tap
“Scan for Devices.” Select your device when it pops up on the screen. Once you pair your Normatec Go, HyperSmart™
will allow you to automatically start your session and control the pressure level and time from within the Hyperice App.
CYBERSECURITY
It is recommended to configure the Hyperice App for automatic updates to ensure cybersecurity. It is also recommended
to keep your Operating System up to date and to configure your Operating System for automatic updates.
ADJUST THE PRESSURE LEVEL
Adjust the pressure level of the session by pressing the pressure level adjustment button on the top left of the control
panel. Pressure level 1 is the gentlest setting. The massage becomes more intense as the pressure level is increased.
Level can be adjusted while the session is running.
ADJUST THE SESSION TIME
Adjust the session time by pressing the time adjustment button. The session time can be set to 15, 30, 45, and 60
minutes. Time can be adjusted while the session is running. Press the time adjustment buttons to cycle through the
session time options to add or subtract time from the session.
START THE SESSION
To start the session, press the Start/Stop button.
PATENTED NORMATEC PULSE MASSAGE PATTERN
The patented Normatec Go massage pattern will begin by compressing your upper ankle. Similar to the kneading and
stroking performed during a massage, each zone of the wrap will first compress in a pulsing manner and then hold as
the compression pattern works its way up your lower limb. When the top zone completes its massage, there will be a
brief rest period and then the cycle will begin again. This will repeat until the session time runs out.
The zones on the wrap are numbered in ascending order from distal zone to proximal zone. Zone 1 corresponds
to the upper ankle, Zone 2 corresponds to the lower calf, and Zone 3 is the upper calf.
STOP OR PAUSE THE SESSION
To stop the session at any time, press the start/stop button. This will pause the session. To restart your paused
session, press the start/stop button again. If you are done using the system, remove the wraps from your limbs, and
turn off the control unit by pressing the power button.
To Next Page
Loading...
Need help?
General