North Star M157305B - User Manual

Questions and Answers

P
Pamela SmithSep 9, 2025
How to resolve poor detergent supply in North Star M157305B?
- A
  Allison GeorgeSep 9, 2025
  If you're experiencing poor or no detergent supply with your North Star Pressure Washer, consider the following: 1. Adjust the soap control knob to a higher setting. 2. Refill the detergent container, ensuring the chemical strainer is fully submerged. 3. Use a shorter high-pressure hose and move the machine closer to your work. 4. Clean the chemical strainer, and always start with a clean detergent container. 5. Clean or replace the injector check valve, and run clean water through the injector after each use.
M
Mr. Robert RichardsAug 23, 2025
How to fix North Star M157305B Pressure Washer that will not run at all?
- K
  Kaitlin PatelAug 23, 2025
  If your North Star Pressure Washer won't run and has no power, there are a couple of things to check. First, ensure that the pump switch is turned ON. Second, check the building's circuit breaker to see if it has tripped.
E
emurrayAug 25, 2025
What to do if North Star M157305B Pressure Washer runs but surges or cycles while in bypass?
- A
  andrew17Aug 25, 2025
  If your North Star Pressure Washer runs but surges or cycles while in bypass, there are a couple of things to check: * Check all connections between the unloader and gun for leaks. Tighten any loose components and replace damaged ones. * Consider replacing the spray gun, as it may be leaking internally.
S
staceytaylorAug 27, 2025
How to fix low pressure on North Star Pressure Washer?
- B
  Brittany NealAug 27, 2025
  If your North Star Pressure Washer has low pressure, it could be due to a couple of reasons: * Ensure the water supply provides more than 4 gpm. * Clean or replace the nozzle if it's partially clogged or damaged.
J
John ValdezAug 27, 2025
How to fix low pressure on a North Star Pressure Washer?
- T
  Travis SmithAug 27, 2025
  If your North Star Pressure Washer has low pressure, ensure the water supply provides more than 4 gpm. Also, inspect the nozzle for clogs or damage; clean or replace it if necessary.
R
Roger LoveAug 29, 2025
How to troubleshoot a North Star M157305B Pressure Washer that will not run due to no power?
- K
  Kyle CoxAug 29, 2025
  If your North Star Pressure Washer isn't running and has no power, there are several things to check: * First, ensure the machine is properly plugged in. * If it is, check the GFCI and make sure the machine is dry, then press the RESET button on the GFCI. * Verify that the pump switch is turned ON. * Finally, inspect the building's circuit breaker to see if it has tripped.
K
Kevin RoachSep 18, 2025
What causes a North Star Pressure Washer to surge or cycle in bypass?
- T
  Teresa WrightSep 18, 2025
  If your North Star Pressure Washer runs but surges or cycles while in bypass, check all connections between the unloader and gun for leaks, tightening loose components and replacing damaged ones. Also, if the gun is leaking internally, replace the spray gun.
J
John AdamsSep 18, 2025
Why is there smoke coming from the heat exchanger on my North Star Pressure Washer?
- J
  John PetersonSep 22, 2025
  If you notice smoke coming from the heat exchanger of your North Star Pressure Washer, adjust the air band until the burner burns cleanly. Also, use kerosene for the cleanest burn, as poor quality fuel may be the cause.
S
Steven ButlerSep 7, 2025
Why does the circuit breaker trip when I use my North Star M157305B Pressure Washer?
- F
  Felicia NealSep 7, 2025
  If the circuit breaker trips when using your North Star Pressure Washer, there are several potential causes. Start by checking the voltage to ensure it is sufficient. Next, make sure that no other equipment is using the same circuit, as this could overload the breaker. Finally, check the pressure setting on the unloader and adjust if it is set too high.
C
carrollkevinSep 4, 2025
What causes a North Star M157305B to surge or cycle while in bypass?
- K
  kristen37Sep 4, 2025
  If your North Star Pressure Washer surges or cycles while in bypass, it could be caused by: * A leak between the pump and gun. Inspect all connections and tighten any loose components, replacing damaged ones as needed. * The spray gun leaking internally. If this is the case, replace the spray gun.