Pressing the Write button while this page is displayed starts the Restore procedure.
The parameter is “Restore from ROM:”. In this case with a value of One program.
This parameter allows the factory Programs, Performances & Global data & Arp Pattern data to be restored to the Factory settings.
Use the lower Data knob to adjust this parameter. Whatever selection is made with the lower Data knob is restored into memory (
ERASING WHAT WAS THERE!!) when the “Write” button is pressed while in this mode. Additional pages appear depending on the
selection. i.e. if “All data” is selected Supernova II Rack asks for confirmation which is set with the lower Data knob, if you set this
to “Yes” & press the “Write” button again all the factory setting will be restored. If however “One prog” was selected Supernova II
Rack asks which Program you want to restore, which is selected using the lower Data knob, & then pressing the “Write” button
again Supernova II Rack asks for the location ( Program bank & number ) that you wish to store the program in. The range of this
parameter is One prog, One perf, One patt, All progs, All perfs, All patts, Prog Change table, Globals, All data, Prog bank A, Prog
bank B, Prog bank C, Prog bank D, Perf bank A, Perf bank B, Dmap a, Dmap b, Dmap c & Dmap d.
Page 9 looks like so:
The higher parameter is “Input/sw 1”. In this case with a value of Audio in.
This parameter determines what the Input/sw 1 input is going to do. Use the higher Data knob to adjust this parameter. In the
Audio in position the Input is configured to accept external audio signals. In the Switch position the input is configured to work as a
Footswitch input. In this case a Footswitch that is normally open. In the Switch-I position the input is configured to work as a
Footswitch input. In this case a sustain pedal that is normally closed. The range of this parameter is Audio in, Switch & Switch-I.
This parameter is memorised as Global.
The lower parameter is “Input/sw 2”. In this case with a value of Audio in.
This parameter determines what the Input/sw 2 input is going to do. Use the lower Data knob to adjust this parameter. In the Audio
in position the Input is configured to accept external audio signals. In the Switch position the input is configured to work as a
Footswitch input. In this case a Footswitch that is normally open. In the Switch-I position the input is configured to work as a
Footswitch input. In this case a sustain pedal that is normally closed. The range of this parameter is Audio in, Switch & Switch-I.
This parameter is memorised as Global.
Page 10 looks like so:
The parameter is “Pedal/sw 3”. In this case with a value of Pedal-R.
This parameter determines what the Pedal/sw 3 input is going to do. Use the higher Data knob to adjust this parameter. In the
Pedal-R position, the input is configured to work as an Expression Pedal input & can mapped into any controller using the
Pedal/breath parameter on page 4 of this menu. In this case an Expression Pedal with the control output on the ring of the pedal
jack. In the Pedal-T position, the input is configured to work as an Expression Pedal input & can mapped into any controller using
the Pedal/breath parameter on page 4 of this menu. In this case an Expression Pedal with the control output on the tip of the pedal
jack. i.e. a Korg EXP2 Expression Pedal. In the Switch position the input is configured to work as a Footswitch input. In this case a
Footswitch that is normally open. In the Switch-I position the input is configured to work as a Footswitch input. In this case a sus-
tain pedal that is normally closed. The range of this parameter is Pedal-R, Pedal-T, Switch & Switch-I. This parameter is memo-
rised as Global.
Pedal/sw 3 Pedal-R
Input/sw 1 Audio in
Input/sw 2 Audio in
To Next Page
Loading...
