To Next PageTo Next Page
Need help?Do you have a question about the NuAire MEVDC and is the answer not in the manual?
Signifies a general warning regarding hazard specified by supplementary information.
Unit must be completely electrically isolated before any panels are removed. Check mains supply and control connections.
Unit contains fast moving rotational parts which may start automatically.
Read and understand the installation and maintenance manual before installing, operating or maintaining this product.
Signifies a general warning regarding hazard specified by supplementary information.
Unit must be completely electrically isolated before any panels are removed. Check mains supply and control connections.
Unit contains fast moving rotational parts which may start automatically.
Read and understand the installation and maintenance manual before installing, operating or maintaining this product.
Keep these instructions in a location where they are accessible to all users at all times.
Always include the operating instructions when you pass the product on to third parties.
Minimum Personal Protective Equipment (PPE) recommendations for handling Nuaire product.
Nuaire's MEV-DC units provide continuous mechanical extract ventilation to homes.
The case is constructed in grey/blue ABS plastic with an acoustically lined access cover.
Explains the model code structure for Nuaire's MEV-DC units.
Installation must be carried out by competent personnel conforming to regulations.
The fan must be fitted indoors, away from water spray, at any angle using the integral mounting bracket.
Assumes compatible ductwork is installed for 125mm discharge and 100/110x54mm inlet spigots.
Unit not fitted with a backdraught shutter; available from Nuaire if required.
Install the integral mounting bracket by marking fixing points and securing with screws.
Locate unit into bracket slots, fix, and adjust dampers using a screwdriver.
Provides detailed dimensions for the unit, including side, end, and top views.
Details available spigot positions for blanking plates, 100mm, and 125mm spigots.
Ensure the unit and controls are electrically isolated from the mains supply before work.
The unit is designed to operate continuously, with boost facility for higher duty.
Boost achieved via Switched Live (SL), Optional Remote Speed Control (OPUS-SPD), or Internal Humidistat.
For EMC, sensor/switched live cables should not be placed within 50mm of other cables.
Diagram showing connections to the circuit board for various functions.
Wiring diagram for a unit serving a bathroom only, including optional lamp.
Wiring diagram for a unit serving a kitchen and bathroom, with room light.
Wiring diagram for a unit serving a kitchen and two bathrooms, with room lights.
Shows the adjustment dial for the internal humidistat, ranging from 50% to 80%.
Unit has two control dials for trickle and boost duties to control airflow rate.
IMPORTANT: The unit must not be switched off; it is designed to run continuously.
The run-on timer adjustment is from 0-60 minutes and is available from the switched live signal.
Details the meaning of the green and red status lights for fan running, failure, or setup.
It is important that maintenance checks are recorded and the schedule is adhered to.
Includes tightening electrical terminals, checking earth connections, and inspecting/cleaning components.
5-year warranty: parts and labour for year 1, replacement parts only for remaining period.
Warranty is void if equipment is modified, incorrectly applied, misused, or not maintained.
Failure to maintain the unit as recommended will invalidate the warranty.
Nuaire uses largely recyclable components like WEEE streams, metals, and plastics.
Ensure product is made safe from electrical/water supplies before dismantling by a qualified person.
Contact After Sales Department for technical assistance, spare parts, or replacement components.
When ordering spares, quote the unit's serial number and part number if known.
Declaration that the unit complies with essential requirements of the Machinery Directive.
Installer must ensure the entire system is safe and complies with legislation.
Each item of equipment is supplied with documentation for safe installation and maintenance.
The rating plate provides essential data like serial number, unit code, and electrical data.
Instructions on warning labels or notices attached to the unit must be adhered to.
Comply with EC Council Directives 2006/42/EC (Machinery) and 2014/30/EU (EMC).
Where access to moving or live parts is not prevented, guarding to appropriate standard must be fitted.
Electrical installation must comply with relevant local electrical safety regulations.
For EMC, control/sensor cables should not be placed within 50mm of power cables.
General pre-commissioning checks include ensuring no foreign bodies and checking electrical safety.
Equipment access panels must be in place and secured with original fastenings during operation.
If failure occurs, take unit out of service until a competent person can effect repair or examination.
It is important that the correct tools are used for the various maintenance tasks required.
If access panels are removed, the electrical supply must be isolated first.
Allow a minimum of two minutes after electrical disconnection before removing access panels.
Caution: Airflow can cause impeller to 'windmill' even when power is not present.
Take care when removing and storing access panels in windy conditions.
General
