Numatic TTB 4045/100 - User Manual

Other manuals for Numatic TTB 4045/100

Owner's Instructions24 pages

Questions and Answers

C
cathyphillipsAug 16, 2025
Why is my Numatic Scrubber not picking up water well?
- B
  Brandi FergusonAug 16, 2025
  If the Numatic Scrubber isn't picking up water effectively, possible causes and solutions include: * Waste-water tank full: Empty the waste-water tank. * Clogged / blocked vacuum hose: Remove and clean the hose. * Loose hose connections: Push the connections tight. * Debris basket filter clogged / blocked: Remove and clean the filter. * Separator filter clogged / blocked: Remove and clean the filter. * Poor separator seal: Clean and refit the seal. * Low battery charge: Recharge the batteries.
S
ssanchezAug 19, 2025
What to do if my Numatic Scrubber has no water flow?
- C
  courtney65Aug 19, 2025
  If your Numatic Scrubber has little to no water flow, consider these potential causes: * Clean-water tank empty: Fill the clean-water tank. * Clean-water tank filter blocked / clogged: Remove and clean the filter. * Clean water tap not turned on: Turn on the clean water tap.
M
moranmichaelAug 22, 2025
Why is there no brush or scrub function on my Numatic Floor Machine?
- M
  Michelle SellersAug 22, 2025
  If your Numatic Floor Machine has no brush or scrub function, first check if the brushes are properly fitted. If not, fit them correctly. Also, the brush may be overloaded, in that case reset the machine.
U
uhendersonAug 25, 2025
How to troubleshoot a Numatic Scrubber that will not operate?
- J
  Jennifer RomeroAug 26, 2025
  If your Numatic Scrubber won't operate, check the following: * Missing or blown fuses: Fit or replace the fuse. * Battery not connected: Connect the battery. * Low battery charge: Charge the batteries.
S
Sara AndersonAug 27, 2025
Why does my Numatic Scrubber keep stopping during operation?
- H
  Heather LiuAug 28, 2025
  If your Numatic Scrubber stops while operating, it may be due to: * Too much load on the brush system: Reset the machine and decrease the brush load to better suit the floor type. * Blown fuse in Battery pack: Replace the 50 Amp fuse.
A
adamsmeganAug 30, 2025
How do I fix a Numatic Scrubber with no brush function?
- J
  Jennifer MilesAug 30, 2025
  If the Numatic Scrubber's brush or scrub function isn't working, check if: * No brushes fitted: Check and fit the brushes. * Brush overloaded: Reset the machine.
F
floresjacksonSep 2, 2025
What to do if my Numatic Floor Machine just stops while operating?
- W
  wardtoddSep 2, 2025
  If your Numatic Floor Machine stops during operation, it might be due to too much load on the brush system. Try resetting the machine and decreasing the brush load to better suit the floor type. Also, check the battery pack for a blown fuse and replace the 50 Amp fuse if necessary.
E
Erin FloresSep 4, 2025
Why is my Numatic Floor Machine not picking up water well?
- J
  Jorge RuizSep 4, 2025
  If your Numatic Floor Machine isn't picking up water effectively, it could be due to several reasons. First, check if the waste-water tank is full and empty it if needed. Also, inspect the vacuum hose, debris basket filter, and separator filter for any clogs or blockages and clean them. Ensure that all hose connections are tight and the separator seal is properly fitted and clean. If the separator seal, vacuum hose, or floor-tool blades are damaged, consider contacting the service department for replacements. Finally, make sure the batteries are fully charged.
K
Kyle JenkinsSep 7, 2025
How to troubleshoot a Numatic Floor Machine that will not operate?
- B
  browncrystalSep 7, 2025
  If your Numatic Floor Machine isn't operating, start by checking the fuses. Replace any missing or blown fuses. Next, ensure the battery is properly connected. Finally, check the battery charge level and charge the batteries if they are low.
R
Robin MitchellSep 10, 2025
What to do if my Numatic Floor Machine has little or no water flow?
- C
  carterbarbaraSep 10, 2025
  If your Numatic Floor Machine has little or no water flow, ensure the clean-water tank is full. Also, check the clean-water tank filter for any blockages and clean it if necessary. Finally, make sure the clean water tap is turned on.

Summary

General Safety and Information

Operational Warnings and Advice

Important warnings and advice on safe operation and usage.

Battery Management

Precautions When Working With Batteries

Essential safety measures when handling and working with batteries.

Battery Care Guidelines

Quick Set-Up Guide

Handle Positioning and Fuse Installation

Steps to set the handle and install the fuse.

Connecting Tanks and Power

How to connect tanks, vacuum hose, and switch on the machine.

Filling the Clean Water Tank

Instructions for filling the clean water tank.

Machine Set-Up

Fitting the Brushes

Instructions on how to fit the Nulock brush system and PadLoc system.

Floor Tool Setup

Fitting and Lowering the Floor Tool

Filling the Clean-Water Tank

Chemical Handling and Pre-Cleaning

Control of Substances Hazardous to Health (COSHH)

Guidance on using chemicals safely and following COSHH regulations.

Machine Operation

Pre-Scrub Mode

Floor Tool Usage

Setting Cleaning Controls

Machine Modes and Operation

Regular Maintenance

Cleaning Waste-Water Tank and Separator

Cleaning Filters and Clean-Water System Components

Floor Tool Maintenance

Changing the Floor Tool Blades

Machine Charging and Battery Care

Trouble Shooting

Machine Specifications

Numatic TTB 4045/100 Specifications

General

Model	TTB 4045/100
Type	Scrubber
Working Width	450 mm
Brush Speed	150 rpm
Brush Motor Power	400 W
Power	24 V
Brush Size	450 mm
Pad Size	450 mm
Cleaning Width	450 mm
Noise Level	68 dB
Power Supply	Battery
Battery	2 x 12 V