How to resolve wrinkling media on Oce Printer?
To address wrinkling media, enable the [Moist sensitivity] setting if wrinkling is caused by humidity. If wrinkling is structural, set the [Carriage elevation] setting in the RIP to [Highest] and increase the [Vacuum power] settings.
How to fix banding within swaths on Oce Colorado 1640 Printer?
To address banding within swaths, perform automatic maintenance with nozzle optimization. Check the [Vacuum power] setting in the RIP, as too much vacuum power can cause the media to slip. Also, verify that the [Media thickness] setting in the RIP is correct.
What to do for curling media on Oce Printer?
If the media is curling, increase the [Vacuum power] settings in the RIP. You can also set the [Carriage elevation] setting in the RIP to [Highest].
Why is the print not rolled up on my Oce Colorado 1640?
If the print is taped to the take-up roll but the roll winder hasn't wound it up, move the media towards the printer to start the winder. Position the hanging part of the print just above the ground in front of the lower sensor towards the sensor. The printer should then detect the media and start winding automatically.
How to improve adhesion on Oce Colorado 1640?
To improve adhesion, increase the [Extended carriage travel] when printing a small image width. Increase the [Printer platen temperature] and reduce your ink limits in the media profile. Alternatively, change the print mode to a higher quality print mode.
What causes wrinkles in black on Oce Colorado 1640 Printer and how to fix?
To address wrinkles in black, try printing in a higher quality mode. If you are using custom media, consider reducing the amount of K ink in the ICC profiling process.
What causes fisheye on Oce Colorado 1640 and how to resolve it?
To resolve fisheye, try printing in a different print mode. You can also decrease the [Printer platen temperature] in the RIP or load a different media type.
How to resolve waves in media on Oce Colorado 1640?
If you are experiencing waves in the media, increase the [Vacuum power] settings in the RIP.
How to fix drifting media on Oce Printer?
If the media is drifting, ensure that the printer platen is clean. Reload the media roll, making sure the media has a straight cut leading edge.
Why is there color banding on my Oce Colorado 1640 Printer?
Color banding may occur during printing. Try selecting a higher quality print mode such as [High Quality], [Specialty], [Backlit], or [Reliance]. If this does not resolve the issue, perform a printhead carriage calibration.
Provides an overview of the operation guide's content and structure.
Describes the different user roles and their responsibilities in the printer workflow.
Introduces the Océ Colorado 1640 printer and its core technology.
Details safety precautions and necessary documents for operating the printer.
Explains typography, safety symbols, and important notes within the manual.
Lists additional resources and where to find them for comprehensive support.
Identifies components accessible from the media output side of the printer.
Details the components of the printer's roll winder system.
Describes the components located on the left and right sides of the printer.
Identifies components accessible from the media input side of the printer.
Details the components within the printer's media drawer.
Illustrates the components visible when the printer's top cover is opened.
Outlines the standard process for handling and using media with the printer.
Explains how to configure media profiles within the RIP software.
Step-by-step guide to installing media profiles using Onyx RIP software.
Instructions for creating custom media profiles using Onyx RIP software.
Guide to duplicating and modifying existing media profiles in Onyx.
Describes how to synchronize and remove media types within Onyx.
Explains media profile management procedures within Caldera RIP software.
Step-by-step guide to installing media profiles using Caldera RIP software.
Instructions for creating custom media profiles using Caldera RIP software.
Guide to duplicating and modifying existing media profiles in Caldera.
Describes how to synchronize and remove media types within Caldera.
Guidance on selecting the appropriate media category for profiles.
Details how to adjust various media settings for optimal print quality.
Explains how to select the most suitable print mode for different applications.
Step-by-step instructions for loading a media roll into position 1.
Step-by-step instructions for loading a media roll into position 2.
Procedure for calibrating the media to ensure accurate printing.
How to define leading or trailing strips for jobs by default.
Instructions for mounting a take-up roll core onto the roll winder.
Overview of different winding options available for media types.
Procedure for printing and winding media without using a tension bar.
Procedure for printing and winding media using a tension bar.
Procedure for printing and winding stiff media with a locked tension bar.
Instructions for printing media without engaging the winding mechanism.
Procedure for cutting the media using the printer's embedded knife.
Instructions for manually cutting the media using a separate knife or scissors.
Steps to safely remove a printed media roll from the roll winder.
Procedure for removing a media roll from the printer's media drawer.
Provides a comprehensive overview of the job printing process.
Detailed steps for submitting and printing a job via the RIP.
Describes how to manage jobs (pause, cancel, resume, stop, move) on the operator panel.
Explains how to interpret status indicators and colors on the operator panel.
Guide to monitoring the printer remotely using the PRISMAsync app.
Guidelines and procedures for printhead maintenance.
Steps to initiate automatic printhead maintenance cycles.
Instructions for performing manual printhead and system maintenance.
Detailed procedure for cleaning key maintenance station components.
Step-by-step guide for cleaning the printer's matrix plate.
Procedure for safely refilling ink cartridges.
Instructions for replacing the printer's maintenance tray.
Guide on how to replace the wiper blade for print quality.
Steps for replacing the printer's cutting knife.
Procedure for replacing optional emission filters in the printer.
Instructions for replacing the lubricators on the printer's carriages.
Procedure for refilling the printer's chiller with demineralized water.
Steps for vacuuming the printer's chiller for optimal performance.
Guide for cleaning the ink unit and surrounding areas.
Lists all necessary maintenance materials and their usage.
Outlines the systematic approach to diagnose and improve print quality.
Procedure for printing a chart to assess printhead performance.
Guide to interpreting the printhead quality check chart results.
Steps to calibrate the printhead for optimal color density and performance.
Procedure for calibrating the printhead carriage for image registration.
Details on setting up and managing the printer's network connection.
Instructions for enabling and configuring remote service access.
How to access the printer's settings editor via a web browser.
Steps to log into the system with administrator privileges.
Guide to changing the system administrator password for security.
Setup instructions for a mail server to enable password recovery.
Steps to resolve issues with mail server configuration.
Procedure to recover a forgotten system administrator password.
Overview of the printer's security features and protocols.
Explains the types of certificates used for secure communication.
Guide to importing trusted certificates for secure server connections.
Steps to enable secure HTTPS communication for settings editor access.
Guidance on resolving issues related to HTTPS certificate implementation.
How to adjust HTTPS security settings for compatibility.
Instructions for installing operating system security patches.
Setup for the PRISMAsync Remote Control app and cloud services.
Procedure to test the connection for PRISMAsync Remote Control.
How to add or remove users for the PRISMAsync Remote Control app.
Steps to create a backup of printer configuration and data.
Procedure for restoring printer configuration from a backup file.
Settings to control system installation or reinstallation via USB.
Provides helpful advice for optimal use and maintenance of the printer.
Information on changing system settings like language and measurement units.
How to configure energy saving modes like auto wake-up and shutdown.
Procedure for downloading job logs to check print properties and counters.
Guidance on relocating the printer; contact service representative.
Instructions for powering the printer on and off.
Basic steps for general troubleshooting and stopping the printer.
Procedure for restarting the printer system.
Steps to power on the printer after an interruption in power supply.
Instructions for clearing media jams or carriage crashes.
How to cancel a maintenance tray replacement procedure.
Troubleshooting guides for specific print quality issues like banding.
Steps to resolve banding artifacts appearing at swath boundaries.
Troubleshooting guide for banding issues occurring within print swaths.
Procedure to address wrinkles appearing in black areas of the print.
Steps to resolve graininess issues caused by ink drop distribution.
Troubleshooting guide for unsharp lines or text due to ink spreading.
Procedure to fix fisheye defects, characterized by tiny white dots.
Steps to resolve smudging issues caused by uncured ink.
Troubleshooting guide for ink adhesion problems on vinyl media.
How to prevent media from touching the printhead, causing pollution or smudges.
Guides to resolve issues related to media handling and transport.
Procedure to address media wrinkling caused by humidity or improper feeding.
Troubleshooting guide for media moving in a wave motion due to low vacuum.
Steps to resolve media curling issues at the leading or side edges.
Procedure to fix media drifting on the platen due to uneven rolling or feeding.
Guidelines for safely cleaning uncured ink from printer components.
Instructions for cleaning the media cover of ink pollution.
Procedure for cleaning the printer's platen area.
Steps for cleaning the guide plate and replacing associated parts.
Provides an overview of the operation guide's content and structure.
Describes the different user roles and their responsibilities in the printer workflow.
Introduces the Océ Colorado 1640 printer and its core technology.
Details safety precautions and necessary documents for operating the printer.
Explains typography, safety symbols, and important notes within the manual.
Lists additional resources and where to find them for comprehensive support.
Identifies components accessible from the media output side of the printer.
Details the components of the printer's roll winder system.
Describes the components located on the left and right sides of the printer.
Identifies components accessible from the media input side of the printer.
Details the components within the printer's media drawer.
Illustrates the components visible when the printer's top cover is opened.
Outlines the standard process for handling and using media with the printer.
Explains how to configure media profiles within the RIP software.
Step-by-step guide to installing media profiles using Onyx RIP software.
Instructions for creating custom media profiles using Onyx RIP software.
Guide to duplicating and modifying existing media profiles in Onyx.
Describes how to synchronize and remove media types within Onyx.
Explains media profile management procedures within Caldera RIP software.
Step-by-step guide to installing media profiles using Caldera RIP software.
Instructions for creating custom media profiles using Caldera RIP software.
Guide to duplicating and modifying existing media profiles in Caldera.
Describes how to synchronize and remove media types within Caldera.
Guidance on selecting the appropriate media category for profiles.
Details how to adjust various media settings for optimal print quality.
Explains how to select the most suitable print mode for different applications.
Step-by-step instructions for loading a media roll into position 1.
Step-by-step instructions for loading a media roll into position 2.
Procedure for calibrating the media to ensure accurate printing.
How to define leading or trailing strips for jobs by default.
Instructions for mounting a take-up roll core onto the roll winder.
Overview of different winding options available for media types.
Procedure for printing and winding media without using a tension bar.
Procedure for printing and winding media using a tension bar.
Procedure for printing and winding stiff media with a locked tension bar.
Instructions for printing media without engaging the winding mechanism.
Procedure for cutting the media using the printer's embedded knife.
Instructions for manually cutting the media using a separate knife or scissors.
Steps to safely remove a printed media roll from the roll winder.
Procedure for removing a media roll from the printer's media drawer.
Provides a comprehensive overview of the job printing process.
Detailed steps for submitting and printing a job via the RIP.
Describes how to manage jobs (pause, cancel, resume, stop, move) on the operator panel.
Explains how to interpret status indicators and colors on the operator panel.
Guide to monitoring the printer remotely using the PRISMAsync app.
Guidelines and procedures for printhead maintenance.
Steps to initiate automatic printhead maintenance cycles.
Instructions for performing manual printhead and system maintenance.
Detailed procedure for cleaning key maintenance station components.
Step-by-step guide for cleaning the printer's matrix plate.
Procedure for safely refilling ink cartridges.
Instructions for replacing the printer's maintenance tray.
Guide on how to replace the wiper blade for print quality.
Steps for replacing the printer's cutting knife.
Procedure for replacing optional emission filters in the printer.
Instructions for replacing the lubricators on the printer's carriages.
Procedure for refilling the printer's chiller with demineralized water.
Steps for vacuuming the printer's chiller for optimal performance.
Guide for cleaning the ink unit and surrounding areas.
Lists all necessary maintenance materials and their usage.
Outlines the systematic approach to diagnose and improve print quality.
Procedure for printing a chart to assess printhead performance.
Guide to interpreting the printhead quality check chart results.
Steps to calibrate the printhead for optimal color density and performance.
Procedure for calibrating the printhead carriage for image registration.
Details on setting up and managing the printer's network connection.
Instructions for enabling and configuring remote service access.
How to access the printer's settings editor via a web browser.
Steps to log into the system with administrator privileges.
Guide to changing the system administrator password for security.
Setup instructions for a mail server to enable password recovery.
Steps to resolve issues with mail server configuration.
Procedure to recover a forgotten system administrator password.
Overview of the printer's security features and protocols.
Explains the types of certificates used for secure communication.
Guide to importing trusted certificates for secure server connections.
Steps to enable secure HTTPS communication for settings editor access.
Guidance on resolving issues related to HTTPS certificate implementation.
How to adjust HTTPS security settings for compatibility.
Instructions for installing operating system security patches.
Setup for the PRISMAsync Remote Control app and cloud services.
Procedure to test the connection for PRISMAsync Remote Control.
How to add or remove users for the PRISMAsync Remote Control app.
Steps to create a backup of printer configuration and data.
Procedure for restoring printer configuration from a backup file.
Settings to control system installation or reinstallation via USB.
Provides helpful advice for optimal use and maintenance of the printer.
Information on changing system settings like language and measurement units.
How to configure energy saving modes like auto wake-up and shutdown.
Procedure for downloading job logs to check print properties and counters.
Guidance on relocating the printer; contact service representative.
Instructions for powering the printer on and off.
Basic steps for general troubleshooting and stopping the printer.
Procedure for restarting the printer system.
Steps to power on the printer after an interruption in power supply.
Instructions for clearing media jams or carriage crashes.
How to cancel a maintenance tray replacement procedure.
Troubleshooting guides for specific print quality issues like banding.
Steps to resolve banding artifacts appearing at swath boundaries.
Troubleshooting guide for banding issues occurring within print swaths.
Procedure to address wrinkles appearing in black areas of the print.
Steps to resolve graininess issues caused by ink drop distribution.
Troubleshooting guide for unsharp lines or text due to ink spreading.
Procedure to fix fisheye defects, characterized by tiny white dots.
Steps to resolve smudging issues caused by uncured ink.
Troubleshooting guide for ink adhesion problems on vinyl media.
How to prevent media from touching the printhead, causing pollution or smudges.
Guides to resolve issues related to media handling and transport.
Procedure to address media wrinkling caused by humidity or improper feeding.
Troubleshooting guide for media moving in a wave motion due to low vacuum.
Steps to resolve media curling issues at the leading or side edges.
Procedure to fix media drifting on the platen due to uneven rolling or feeding.
Guidelines for safely cleaning uncured ink from printer components.
Instructions for cleaning the media cover of ink pollution.
Procedure for cleaning the printer's platen area.
Steps for cleaning the guide plate and replacing associated parts.
To Next Page
General
