Why is there no end-of-job notification from Oki B6300 Printer?
If you're not getting end-of-job notifications from your Oki Printer, specify the NOTIFY option when sending jobs from your computer. Also, make sure the NetWare CASTON utility is executed on the computer, not the CASTOFF utility.
Why am I getting no notification of Oki Printer errors?
If you're not receiving notifications for Oki Printer errors, ensure your user name and group name are registered in the Notify Candidate List of the print server. Register them in the Notify section.
What to do if Oki Printer says please reboot printer?
If your Oki Printer displays 'Please reboot printer,' switch off the printer, then switch it on again. This will resolve errors occurring in the NetWare interface.
Why is my Oki B6300 Printer not printing?
If your Oki Printer isn't printing, first, ensure the correct IP address is set. If LPD spool is set to Memory, and a single print file exceeds the receiving capacity, split the file into smaller parts. If multiple files exceed the limit, reduce the number of files sent at once. For an irrecoverable error, try turning the printer off and then on again. If the print data format is different, disable the Ctrl-D output function.
How to delete documents from Oki B6300 window?
If you can't delete documents from the Oki Printer window, select the document and choose 'Cancel Printing' from the Document menu. Note that deleting all documents is only for the printer administrator. If you are not the owner of the document, log in to Windows using the owner's name. If you're using Windows NT 4.0, make sure Service Pack 3 or above is installed.
Why is my Oki B6300 not found?
If your Oki Printer is not found, make sure the transport protocol is the same for both the client computer and the printer. If there are multiple browsers, set the Auto Master Mode in the config.txt file to Off and reboot the printer. If the printer and client computer are on different networks, contact your system administrator. Check the config.txt file settings (WINS Primary Server, WINS Secondary Server, Subnet Mask) against the client computer settings. If the host name already exists, change it in the config.txt file or reset the printer settings.
What to do if the Ready light is blinking but my Oki B6300 isn't printing?
If the Ready light is blinking but there is no print output from your Oki Printer, there are likely jobs remaining in the printer's memory. Cancel the current printing job or force the remaining data to print.
Why is Oki Printer connected but not printing?
If your Oki Printer is connected but not printing, first, press the button. If that doesn't work, and the print languages of the printer and driver differ, set them to the same language.
How to get desired print results if Oki Printer is printing wrong?
To get the desired print results from your Oki Printer, set the same print language for both the print job and the printer.
How to obtain desired print results from Oki Printer?
To get the desired print results from your Oki Printer, ensure the print language specified matches the language of the print data. Also, use the printer driver that came with the printer. If you use a driver from another company, the printer might not print correctly.
Information on necessary knowledge before using the printer and software.
Summary of each chapter's content.
Details the operating systems and network environments supported by the printer.
Steps to install and set up printing via LPD or Port9100 on Windows NT 4.0/2000/XP/Server 2003.
Overview of system configuration and lists target computers for LPD/Port9100.
Steps to install and set up printing using the Internet Printing Protocol (IPP).
Overview of IPP system configuration, target computers, and printer driver installation.
Steps to install and set up printing via SMB on a Windows network.
Details on modifying SMB settings using the [Config.txt] file.
Setting up the feature for automatic printer driver download over SMB.
Steps to install and set up printing to a Novell NetWare network.
Overview of NetWare system configuration, target computers, and IPX/SPX frame types.
Procedure for printing from a UNIX computer using LPD, including system configuration and target computers.
Steps for setting up the printer and configuring workstations for UNIX printing.
Details on commands like lpr, lprm, lpq, lp, cancel, lpstat, and the -C option for UNIX printing.
Steps to install and set up printing from a Macintosh computer.
Overview of Macintosh printing system, target computers, and OS support.
Tool to set printer IP address via TCP/IP or MAC address.
Tool to configure NetWare server and printer settings.
Tool to monitor network printer status via an icon or dialog box.
Step-by-step guide on how to use the Simple Status Notification tool.
Precautions and limitations when using the printer with TCP/IP.
Precautions and limitations when using the printer with SMB.
Precautions and limitations when using the printer with NetWare.
Possible causes and solutions for TCP/IP printing errors.
Possible causes and solutions for SMB printing errors.
Possible causes and solutions for NetWare printing errors.
Possible causes and solutions for EtherTalk printing errors.
Procedure for setting printer configuration using Telnet.
Steps to manually set the printer's IP address via the control panel.
General| Print Technology | LED |
|---|---|
| Resolution | 1200 x 1200 dpi |
| Monthly Duty Cycle | Up to 100, 000 pages |
| Connectivity | Ethernet |
| Memory | 64 MB, upgradable to 320 MB |
| Duplex Printing | Standard |
| Printer Language | PCL 5e, PCL 6, PostScript 3 |
To Next Page
