14
rESrES
rESrES
rES A utomatic Reset Time. Select
OFF OFF
OFF OFF
OFF,
0.10.1
0.10.1
0.1 to
99.9 99.9
99.9 99.9
99.9 min utes . Select
OFF OFF
OFF OFF
OFF
to s witch to
OFSOFS
OFSOFS
OFS.
#OFS (948) or
OFSOFS
OFSOFS
O F S Man ual Offset Correction Select
OFFOFF
OFFOFF
OFF
,,
,,
,
0.1 0.1
0.1 0.1
0.1 to
99.9%99.9%
99.9%99.9%
99.9%. Select
OFF OFF
OFF OFF
OFF to
switch to
rES rES
rES rES
rES.
#rtE (948) or
rr
rr
r
tEtE
tEtE
tE Rate Time. Select
OFFOFF
OFFOFF
OFF
,,
,,
,
0.01 0.01
0.01 0.01
0.01 to
99.99 99.99
99.99 99.99
99.99 minutes , Der ivative.
SECONDSECOND
SECONDSECOND
SECOND
ARAR
ARAR
AR
Y MENU (cont'd)Y MENU (cont'd)
Y MENU (cont'd)Y MENU (cont'd)
Y MENU (cont'd)
SLOSLO
SLOSLO
S L O PID values are preset for a slo w response process.
nornor
nornor
nor PID values are preset for a nor mal response process.
FF
FF
F
AStASt
AStASt
ASt PID values are preset for a fast response process.
Pid2Pid2
Pid2Pid2
Pid2 Linkage of PID parameters between SP1 and SP2: Select
OnOn
OnOn
On or
OFFOFF
OFFOFF
OFF.
OnOn
OnOn
O n Links SP2 to SP1
or #SP1
rEs and r tE ter ms for heat/cool applications .
OFFOFF
OFFOFF
O F F Sp2 functions without rEs and r tE.
ArUPArUP
ArUPArUP
ArUP Anti- Reset Wind-up Feature: Select
OnOn
OnOn
On or
OFFOFF
OFFOFF
OFF.
OnOn
OnOn
O n When ArUP is
On On
On On
On the accumulated Reset Offset v alue will be cleared to 0%
when the process input is not within the Propor tional Band.
OFFOFF
OFFOFF
O F F When ArUP is
OFFOFF
OFFOFF
O F F, the accumulated Reset Offset Value is retained in
memory when the process input is not within the Propor tional Band.
ArAr
ArAr
Ar
tEtE
tEtE
tE Approach Rate Time: Select
OFFOFF
OFFOFF
OFF
,,
,,
,
0.01 0.01
0.01 0.01
0.01 to
99.9999.99
99.9999.99
99.99 minutes . The function defines the
amount of Rate applied when the input is outside of the Propor tional Band. The Ar tE
time and the r tE time are independent and have no effect on each other. To
increase damping effect and reduce o vershoot set the approach r ate time f or a v alue
greater than the natur al r ise time of the process (natur al r ise time = process value
time to set point).
PEAPEA
PEAPEA
P E A The Peak feature will remember the highest input the Instr ument has had since the
last reset or Pow er On. At Pow er On it is reset to the present input. To man ually reset
the v alue , PEA must be in the lo w er displa y and then press the
ENTERENTER
ENTERENTER
ENTER key. This will
cause PEA to be reset to the present input value.
UU
UU
U
ALAL
ALAL
A L The Valley feature will remember the low est input the Instr ument has had since the
last reset or Pow er On. At Pow er On it is reset to the present input, and ma y have
to be man ually reset. To m an ually reset the value , V A L m ust be in the lo w er display
and then press the
ENTERENTER
ENTERENTER
ENTER key. This will cause UAL to be reset to the present input
value .
In the follo wing the symbol "#" will be used follo wing letters to ref er to either a n umber "1"
or n umber "2". The "1" will relate to SP1 functions , the "2" for SP2. If y our control is not
equipped with a second set point, no SP2 functions will appear. The appearance of
CY#CY#
CY#CY#
CY#,
SP#dSP#d
SP#dSP#d
SP#d, or
PUL# PUL#
PUL# PUL#
PUL# is dependent upon the output type selected in the Secure Men u item S#Ot.
If time propor tioning (cycle time) w as selected, then CY# is adjustable. If On - Off w as
selected, then SP#d is adjustable. If pulsed time propor tioning w as selected then PUL# is
OUTPUT
0
REVERSE ACTING (S#St = rE
To Next Page
Loading...
