19
CONFIGURACONFIGURA
CONFIGURACONFIGURA
CONFIGURA
TION MENUTION MENU
TION MENUTION MENU
TION MENU
DO NOT ENTER THE CONFIGURATION MENU UNLESS YOU HAVE BEENDO NOT ENTER THE CONFIGURATION MENU UNLESS YOU HAVE BEEN
DO NOT ENTER THE CONFIGURATION MENU UNLESS YOU HAVE BEENDO NOT ENTER THE CONFIGURATION MENU UNLESS YOU HAVE BEEN
DO NOT ENTER THE CONFIGURATION MENU UNLESS YOU HAVE BEEN
INSTRUCTED TO BY ANOTHER PART OF THESE INSTRUCTIONS. INCOR-INSTRUCTED TO BY ANOTHER PART OF THESE INSTRUCTIONS. INCOR-
INSTRUCTED TO BY ANOTHER PART OF THESE INSTRUCTIONS. INCOR-INSTRUCTED TO BY ANOTHER PART OF THESE INSTRUCTIONS. INCOR-
INSTRUCTED TO BY ANOTHER PART OF THESE INSTRUCTIONS. INCOR-
RECT ENTRY OF DATA IN THE CONFIGURATION MENU MAY PREVENTRECT ENTRY OF DATA IN THE CONFIGURATION MENU MAY PREVENT
RECT ENTRY OF DATA IN THE CONFIGURATION MENU MAY PREVENTRECT ENTRY OF DATA IN THE CONFIGURATION MENU MAY PREVENT
RECT ENTRY OF DATA IN THE CONFIGURATION MENU MAY PREVENT
YOUR CONTROL FROM OPERATING PROPERLY.YOUR CONTROL FROM OPERATING PROPERLY.
YOUR CONTROL FROM OPERATING PROPERLY.YOUR CONTROL FROM OPERATING PROPERLY.
YOUR CONTROL FROM OPERATING PROPERLY.
If re-configur ation is required, f ollo w the instr uctions belo w .
The Configuration Menu is used to quic kly configure the instr ument. The configuration for
your par ticular model is sho wn on the Model / Ser ial label located on the top of the
instrument housing. A label found inside on the r ight pr inted circuit board only sho ws the
hardware configur ation and options .
The numbers shown are defined as follows:
The Hardware configur ation code
mm
mm
m
ust notust not
ust notust not
ust not be changed as it defines the hardware f or the
specific instr ument. All other configur ation may be altered if necessar y. It is impor tant that
the codes be correctly entered in order for the instr ument to function proper ly. If an invalid
code number is entered for a par ticular configur ation item, it will not be accepted and the
old configur ation code will be retained.
To re-configure:
1. At pow er up, simultaneously press and hold the
INDEXINDEX
INDEXINDEX
INDEX &
ENTER ENTER
ENTER ENTER
ENTER keys while the lamp
test or self test is displa yed. Hold the k eys do wn until
Hr Hr
Hr Hr
Hr
d1d1
d1d1
d1 appears. A dash appears
in the upper display.
2. Press the
INDEXINDEX
INDEXINDEX
INDEX key to advance through the menu items . Pressing the
INDEXINDEX
INDEXINDEX
INDEX &
DODO
DODO
DO
WNWN
WNWN
WN keys sim ultaneously will bac k up to a menu item. Stop at the menu item you wish
to change.
3. Press the
UPUP
UPUP
UP or
DODO
DODO
DO
WNWN
WNWN
WN key to select the desired Configur ation Code from the following
char t.
4. Press
ENTERENTER
ENTERENTER
ENTER to retain the Configur ation Code.
5. Press
INDEXINDEX
INDEXINDEX
INDEX to advance.
6.If you do not want to retain the re-configur ation, this is y our last chance to retur n to the
old configur ation. Press
ENTER ENTER
ENTER ENTER
ENTER at
AcPt no AcPt no
AcPt no AcPt no
AcPt no to e xit and retain the old configur ation.
Hardware
Option
Configuration
Model CN76
Input Type
Temperature Descriptor
SP1 & SP2 Action
Alarm State
Alarm Action
Alarm Type
To Next Page
Loading...
