Omron H7CX


+&;+&;
'LPHQVLRQV
8QLWPPLQFK
■
'LPHQVLRQVZLWK3DQHO0RXQWLQJ$GDSWHU
■
'LPHQVLRQVZLWK)URQW&RQQHFWLQJ6RFNHW
1RWH 7KHVHGLPHQVLRQVYDU\ZLWKWKHNLQGRI',1WUDFNUHIHUHQFHYDOXH
58
(2.28)
98.57.5
51
106
(4.17)
48
(1.90)
48
(1.90)
58
(2.28)
48
(1.90)
7.5
51
62.5
48
(1.90)
70
(2.76)
58
(2.28)
48
7.5
51
98.7
48
(1.90)
78.5
(3.09)
A
Panel Cutouts
Panel cutouts are
as shown below.
(according to DIN43700).
Note 1. The mounting panel thickness
should be 1 to 5 mm.
3. It is possible to mount counters
side by side, but only in the
direction without the hooks.
If they are mounted side-by-side,
water-resistant specifications
cannot be ensured.
60 min.
60 min.
45
+0.6
−0
45
+0.6
−0
+1
0
A = {48n−2.5 + (n−1) x 4}
With Y92A-48F1 attached.
+1
0
A = (51n−5.5)
With Y92A-48 attached.
+1
0
A = (48n − 2.5)
15 min.
n side by side mounting
2. To allow easier operability, it is
recommended that Adapters are
mounted so that the gap between
sides with hooks is at least 15 mm
(i.e., so that the panel cutout interval
is at least 60 mm).
• +&;$ • +&;$: • +&;$8
• +&;$6 • +&;$:6 • +&;$8'
• +&;$ • +&;$: • +&;$86'
• +&;$6 • +&;$:'
• +&;$:6'
<6RUGHUVHSDUDWHO\
:DWHUSURRI3DFNLQJ
3DQHO
<)RUGHUVHSDUDWHO\
3DQHO0RXQWLQJ$GDSWHU
3*$
RUGHUVHSDUDWHO\
%DFN&RQQHFWLQJ
6RFNHW
<6SURYLGHG
:DWHUSURRI3DFNLQJ
3DQHO
<)SURYLGHG
3DQHO0RXQWLQJ$GDSWHU
<6SURYLGHG
:DWHUSURRI3DFNLQJ
3DQHO
<)SURYLGHG
3DQHO0RXQWLQJ$GDSWHU
6FUHZ7HUPLQDO0RGHOVZLWK([WHUQDO3RZHU6XSSOLHV
3URYLGHGZLWK$GDSWHUDQG:DWHUSURRI*DVNHW
6FUHZ7HUPLQDO0RGHOVZLWKRXW([WHUQDO3RZHU6XSSOLHV
3URYLGHGZLWK$GDSWHUDQG:DWHUSURRI*DVNHW
SLQ6RFNHW0RGHOV
$GDSWHUDQG:DWHUSURRI*DVNHW2UGHUHG6HSDUDWHO\
• +&;$' • +&;$:6'
• +&;$6' • +&;$:6'
• +&;$'
• +&;$6'
• +&;$ • +&;$
• +&;$6 • +&;$6
• +&;$' • +&;$'
• +&;$6'
112
109.7
P2CF-11
H7CX
-A11