Omron HL-5030 - Page 3

HL-5000
Dimensions and Operating Characteristics (Unit: mm)
Switches (Dimensions not shown are the same as roller lever models.)
Note: Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
* Measured with the types of the 31.5-mm arm or rod length.
OF and RF measured at the arm length of 75 mm for HL-5030, and 145 mm for HL-5050 (reference values).
Operating
characteristics
Model
HL-5000 HL-5030 * HL-5050 * HL-5100 HL-5200 HL-5300
Operating force
Release force
Pretravel
Overtravel
Movement Differential
OF max.
RF min.
PT max.
OT min.
MD max.
7.35 N
0.98 N
20°
50°
12°
7.35 N
0.98 N
20°
50°
12°
7.35 N
0.98 N
20°
50°
12°
8.83 N
1.47 N
1.5 mm
4 mm
1 mm
8.83 N
1.47 N
1.5
mm
4 mm
1 mm
1.47 N
−
30 mm
−
−
Operating position OP −−−30±0.8 mm 40±0.8 mm −
HL-5030 HL-5050
OF 3.09 N 1.60 N
RF 0.41 N 0.22 N
17.5 dia. × 6.6
resin roller *1
33
4.1
33
60.6
21.4
58
±0.8
34
53
±0.8
15.5
Three, M3
Rub
ber
connector
31.5R
(19)
16.5
18.5
39.5
±0.8
40.3
±0.8
*2
M5 × 12
Allen-head
bolt
(110)
50
±0.2
24
±0.2
*1. The lever can be mounted anywhere in 360°.
*2. The head can be mounted in any of the four directions.
Two, 5.2 dia.
+0.2
0
mounting holes
Roller Lever
HL-5000
Adjustable
up to 30R
to 75R
4.1
60.6
21.4
65.7
±0.8
60.3
±0.8
51.3
±0.8
15.5
Three, M3
(19)
16.5
39.5
±0.8
32
*2
17.5 dia.
×
6.6 *1
M5
×
12
Allen-head
bolt
M5
×
16
Allen-head
bolt
50
±0.2
*1. Resin roller
*2. The head can be mounted in any of the four directions.
Adjustable Roller Lever
HL-5030
4.1
60.6
21.4
62.8
±0.8
53.4
±0.8
15.5
145 max.
(19)
16.5
*2
3 dia.
×
160 *1
M5
×
12
Allen-head
bolt
M5
×
16
Allen-head
bolt
50
±0.2
*1. Stainless steel rod
*2. The head can be mounted in any of the four directions.
39.5
±0.8
32
5.4
Three, M3
Adjustable Rod Lever
HL-5050
60.6
20.2
(19)
16.5
OP
50
±0.2
4.1
PT
8 dia.
*
* Stainless steel plunger
Two, M 3
Three, M3
Sealed Plunger
HL-5100
60.6
20.2
(19)
16.5
OP
50
±0.2
4.1
PT
12.7 dia.
× 4.8 *1
*1. Stainless sintered alloy roller
*2. The head can be mounted in either of the two directions.
Two, M 3
*2
Three, M3
Sealed Roller Plunger
HL-5200
60.6
20.2
(19)
16.5
110
±2.5
50
±0.2
4.1
*1
*1. Resin rod
*3. The operating range of the dog or cam is the top third (i.e. from the tip of the
rod) of the whole actuator.
Two, M 3
Three, M3
38
±0.2
42
±0.2
30 *2
PT
3.2 dia.
6.6 dia.
*2
*2. The coil spring may be operated from any directions except axial directions ( ).
Coil Spring
HL-5300
http://www.ia.omron.com/
3
(c)Copyright OMRON Corporation 2007 All Rights Reserved.