Onkyo DV-SP800 User Manual (English)

Other manuals for Onkyo DV-SP800

Questions and Answers:

M
michael90Aug 22, 2025
What to do if there is no sound reproduced from Onkyo DV-SP800 DVD Player?
- E
  emily57Aug 22, 2025
  If no sound is coming from your Onkyo DVD Player, there could be several reasons. First, check if the [Digital Out] in the Audio menu is set to [Off], and if so, set it to [On]. Also, make sure that the [Linear PCM Out] setting is not set to [Down Sample Off]. If it is, either connect using the analog outputs, or set [Linear PCM Out] to [Down Sample On]. Check the current sound signal conversion method, and select the right setting. Ensure that the pause mode is not engaged by pressing or II to exit the pause mode. Increase the volume level of your TV or amplifier. If you are playing a DVD or CD recorded in DTS audio, connect the digital output on the player to the digital input on a receiver or amplifier with a built-in DTS decoder.
R
rjonesAug 23, 2025
Why is there no DTS audio output from my Onkyo DV-SP800 DVD Player?
- C
  Charles McdanielAug 23, 2025
  If you're not getting any DTS audio output from your Onkyo DVD Player, and you're connected to a non-DTS compatible amplifier or decoder using a digital audio cable, set [DTS Out] to [DTS ) PCM] in the Setup menu. If you are connected to a DTS-compatible amplifier or decoder using a digital audio cable, check the amplifier settings and ensure the cable is properly connected.
P
petersonaprilAug 25, 2025
How to fix Onkyo DV-SP800 DVD Player remote when it's not working?
- R
  Robert MillsAug 26, 2025
  If the buttons on your Onkyo DVD Player operate, but the remote controller does not, try the following: * Insert new batteries into the remote. * If batteries are already inserted, replace them with new ones. * Ensure that you are pointing the remote controller at the remote sensor of the DVD Player. * Make sure that you are operating the remote controller within 5 meters of the DVD Player.
B
Brandon SpencerAug 27, 2025
Why is the screen stretched on my Onkyo DV-SP800?
- J
  jeffersongregoryAug 27, 2025
  If the screen appears stretched or the aspect ratio doesn't change on your Onkyo DVD Player, it might be due to an incorrect multi aspect setting. To fix this, change the aspect setting in the [TV Screen] setting in the Setup screen Video menu to the screen type most appropriate to the TV or monitor you are using. If your TV is connected with an S-Video cord, the picture may appear stretched. In this case switch the output from [S2] to [Sl].
J
Jessica ColemanAug 27, 2025
Why is the surround sound level low on my Onkyo DV-SP800?
- R
  Ryan WilliamsAug 27, 2025
  If the surround sound level is low on your Onkyo DVD Player, check if the selector switch is set to SURR 1+2. If it is, set the selector switch to SURR 1.
O
oflemingAug 29, 2025
What to do if Onkyo DV-SP800 DVD Player won't play MP3 tracks?
- J
  Jason LyonsAug 29, 2025
  If your Onkyo DVD Player won't play a disc containing MP3 tracks, it could be due to incorrect formatting. Ensure that the tracks are in the MPEGI Audio Layer 3 format and that the sampling rate of the tracks is 44.1 or 48kHz.
K
Kathryn MarshallAug 30, 2025
Why are some MP3 tracks missing from a disc on my Onkyo DVD Player?
- O
  ogarciaAug 30, 2025
  If some MP3 tracks appear to be missing from a disc on your Onkyo DVD Player, it could be due to a few reasons. First, check that the track name ends in “.mp3” or “.MP3”, and if not, change the track name. This player only recognizes the first 250 folders and tracks on a disc. If there are more folders/tracks than this, you will not be able to play them. Also, this player is not compatible with multi-session discs. If the disc is multi-session, you will only be able to play tracks recorded onto the first session.
C
Carrie GarzaAug 31, 2025
Why can't Onkyo DV-SP800 output 96kHz or 88.2 kHz digital audio?
- S
  shannon28Aug 31, 2025
  If your Onkyo DVD Player cannot output 96kHz or 88.2 kHz digital audio, it may be because some discs are digital copy protected. Check that the [Linear PCM] settings is not set to [Down Sample On].
J
johnbellSep 2, 2025
Why does frame search skip frames on Onkyo DV-SP800?
- C
  Connie GarciaSep 2, 2025
  If frame search doesn’t find the frame number input, or some frames are skipped when using frame advance on your Onkyo DVD Player, it may be because you are using discs recorded in 24 frames/second progressive scan format. With these discs, the player ‘misses’ one frame every six frames.
A
Aaron ReedSep 3, 2025
What to do if my Onkyo DVD Player doesn't switch on?
- A
  andrea30Sep 3, 2025
  If your Onkyo DVD Player doesn't switch on, there could be several reasons. First, check that the mains lead is properly connected. Second, ensure that the main power switch is turned on. Finally, there might be external noise in the computer circuits; try switching the main power off and then on again. If that doesn't work, disconnect the mains lead and reconnect it.