Onkyo TX-108

Il PAUSE: Press to activate the Pause mode.
> PLAY: Press to begin playback.
m STOP: Press to stop playback.
W<@ JUMP: Press this key to play soundtracks before
the one being played.
>> JUMP: Press this key to play soundtracks after
the one being played.
Refer to the CD Player instruction manual for additional
instruction to operate the CD player.
Note:
Point the remote control transmitter (RC-108X) tn the
direction of the CD player when using it. The distance
of use of the transmitter may be different for TX-108/88
and the CD player.
OPERATIONS
a
NOTE:
® Before turning power on, confirm that all connections
nave been made properly.
® For remote control operations, refer to the remote
control section.
Standby Mode
The standby position of controls and switches serves as
the starting point for all modes of operation. When the
system power switch is then turned on (while the main
power switch is also on), all controls except the speaker
selector, simulated stereo, Dynamic Transient expander,
dynamic bass expander, Cartridge Selector, Mode Switch,
Loudness, bass, treble, volume, balance controls, APR
Switch, FM Mute Switch are in the same setting as when
the system power switch was last switched off.
Be sure that the APR switch and the FM mute switch are
ON.
Speaker Selector As appropriate
Cartridge Selector (TX-108 only) As appropriate
Mode Switch STEREO
Loudness Control OFF
Bass Control Center
Treble Control! Center
Volume Contro! Minimum
Balance Control Center
Dynamic Bass Expander OFF
Dynamic Bass Expander
Ss) lelsisis[Sioblels!
Level Control (50Hz) Minimum
Dynamic Bass Expander
Level Control! (100Hz) Minimum
(TX-108 only)
Dynamic Transient Expander
Switch (TX-108 only) OFF
Dynamic Transient Expander
fF] fe} 2
Level Control (TX-108 only) Minimum
Simulated Stereo Switch OFF
Key Touch Tone Switch
(Rear Pannel) ON
— VCR-2 Mode Switch
(Rear Pannel) As appropriate
Main Power Switch ON
System Power Switch ON
IN
Tuner Reception
To listen to an FM or AM broadcast, press the TUNER input
selector [8] and confirm that the TAPE-2 monitor [7] is
off.
FM Reception (Manual Mode)
1. Set the FM/AM selector switch to the FM mode.
2. Set the tuning mode switch to the MANUAL mode.
3. To tune in an FM station not stored in the memory, press
the UP or DOWN tuning selector until the frequency
display approaches the frequency of the desired station.
Then release the tuning selector and press it again In
single steps until the desired frequency is tuned pre-
cisely. Note that the frequency is changed in 200 kHz
(or 50 kHz) steps when either tuning selector is pressed
in single steps.
4. To recall a station stored in the memory, simply press
the preset key corresponding to the desired station.
Be sure to set the shift key to the mode (1-8 or
9-16) for the memory channel to be recalled. Since this
is arandom FM/AM memory, an AM station will be
tuned in if you recall a memory channel tn which an
AM station is stored.
5. The stereo indicator will light if the broadcast is
being received in stereo. The stereo indicator will not
light if the broadcast is monaural or too weak to be
received in stereo.
6. Adjust the volume, tone and other controls as desired.
FM Reception (Auto Mode)
1. Set the FM/AM selector switch to the FM mode.
2. Set the tuning mode switch to the AUTO mode.
3. Press the UP or DOWN tuning selector [217]. The tuned
frequency will continue to increase or decrease until a
sufficiently strong broadcast is reached. To move on to
the next broadcast, press either tuning selector again
depending on the direction in which you want to go.
4. To stop scanning during automatic tuning, press the
tuning mode switch to return to the manual mode.
The frequency display will immediately stop increasing
or decreasing.
AM Reception (Manual Mode)
1. Set the FM/AM selector switch to the AM mode.
2. Set the tuning mode switch to the MANUAL mode.
3. To tune in an AM station not stored tn the memory, press
the UP or DOWN tuning selector in the manner
described in the FM section. Note that the frequency
is changed in 10 kHz (or 9 kHz) steps when either tuning
selector is pressed in single steps.
4. To recall a station stored in the memory, simply press
the preset key corresponding to the desired station.
Be sure to set the shift key to the mode (1-8 or
9-16) for the memory channel! to be recalled. Since this
is arandom FM/AM memory, an FM station will be tuned
in if you recall a memory channel in which an FM station
is Stored.
AM Reception (Auto Mode)
1. Set the FM/AM selector switch to the AM mode.
2. Set the tuning mode switch to the AUTO mode.
3. Press the UP or DOWN tuning selector [21]. The tuned
frequency will continue to increase or decrease until a
sufficiently strong broadcast is reached. To move on to
the next broadcast, press either tuning selector again
depending on the direction in which you want to go.
4. To stop scanning during automatic tuning, press the
tuning mode switch to return to the manual mode.
— 10 -