Onkyo TX-902 - AC Outlets (TX-902 only); Connections for Remote Control (REMOTE CONTROL); Direct Function Feature

AC..Outlets..........
go
pcte
ol
suo
nee
sees
@
SWITCHED:
(TX
-902:
monly):
.
:
An
AC
outlet:is
switched
on
and
off
by
the
Power
nee
on
~
the
front
panel:
and
remote
control
transmitter.
‘Capacity
is:
EA00
é
“watts.”
‘
i.
(TX-902 any)
Connections
for
Remote
Control
(REMOTE
CONTROL)
@
The
upper
and.
lower
ARI
remote
control
jacks
have
the
same
function.
®@
Acassette
tape
deck
and
compact
disc
player
that
have
the
Onkyo
fQE
mark
can
be
onetaed:
using
the
accessory
remote
control
transmitter.
TX-902
COMPACT
DISC PLAYER.
FRI REMOTE
CONTROL
CASSETTE...
TAPE DECK aa
FRI REMOTE
e)
CONTROL
An
{21
remote
control
cable
equipped
with
a
1/8”
(3.5mm)
diameter
miniature
two-conductor
phone
plug
is
attached’
to’
the
TX-902
and
to
any
compact
disc
player,
with
the
QE
mark.
To
use
an
Onkyo
compact
disc
player
and
cassette
tape
deck
with
the
(QI
mark,
insert
the
accessory
remote
control
cable
plug
into
the
REMOTE
CONTROL
jacks:
As
far
as
connecting:
:
sequence
is
concerned;.
it
doesn’t
matter
whether
the
cable
is
connected
from
the
TX-902
to
the
cassette
tape
deck
or
to
the
compact
disc
player.
The
remote
control
transmitter
is
operated
by
facing
it
towards
the
remote
control
sensor
of
the
TX
902.
NOTE:
Remote
control
operation
is
not
possible
when
only
the
remote
contro!
cable
is
connected.
Remote
control
cable
and
pin
cord
must be connected.
“TURNTABLE with no FRE mark
“For this special cable. :
**: Contact an Onkyo Service Center.
(TX-902 only)
AC OUTLETS
ACZ40V-L SOlle SWITCHED TQTAL 100W MAX.
Canadian Taodale snl.
lf
you
own
a
Canadian
model
ot
the
TX-902,
the
Onkyo
turntable
can.
be
operated;
uaing
‘the
eeeaeeOry
remote
controh
transmitter.
@
If
your
turntable
has
an
‘RI
mark
on
it,
insert
t
the
sccessory
FRI
remote
control
cable
plug
attached
to
the
Onkyo
turntable
with
the
(4
mark
into
the
PHONO
of
the
TX-902'
s
REMOTE
CONTROL.
@
Onkyo
turntables
that
can
be
remote.
controlled
but
do
not
have
the
(1
mark.
This
equipment
has’a
7-pin
DIN
jack
on
the
rear
panel.
Connect
this
jack
and'the
jack
on
the
rear
of
the
TX-902
with
the
special
cable
for
this
Burnone:!
which
is
. sold separately.
° TURNTABLE with the FBP mark
fo) Al REMOTE ¢
20% CONTROL %
For a turntable
(3.5 mm pin to 7-pin plug cable)
* Sspartnumber;'2010140
Direct function feature
‘NOTE::
This function works when an Onkyo cassette tape deck or
CD
player
with
the
(QI
mark
is
connected
to
a
TX-902
with
an (1 remote control cable.
Just
by
directly
operating
the
desired
component
(compact
disc
player,
or
tape
deck),
the
TX-902’s
input
selector
automatically
switches
to
that
component.
The
component
that
was
being
used
stops,
andthe
desired
component
starts
operation.
Therefore,
it
is
not
necessary
to
switch
the
TX-902's
input
selector
when
changing
listening
sources.
Example :
When.
the
compact
‘disc
player
s
say
urtan
is
pressed,
the
TX-
902’
s
input
selector
will
switch
automatically
to
“CD."
If
the
current.
listening
source
was
a
tape
deck,
tape
playback
will
stop
. and the cone disc meyer will’ start playing.
NOTE:
:
The
direct
function
feature
does
not
apply
to
turntable.
|