Onkyo TX-902 - Remote Control Transmitter; Use of Batteries; Using the Remote Control Transmitter

Remote
control
transmitter
(TX-902
only)
Power Button (POWER) ... ..
Phono
Operation
Button
(PLAY/REJECT)
(RC-183S
only)
bal
teers
attests
een
ce
This
button
is
used
to
operate
the
turntable.
~
The
phono
operation
button
can
be
used
only.
when
the
PHONO
input
selector
button
has...
been
pressed.
Each
time
the
phono
operation"
button
is
pressed,
the
remote
control
transmitter
ane
alternately
emits
the
play
or
reject
command...
CD
Operation
Buttons
(CD)
These
buttons
are
used.
to
Operate
an
ONKYS:
CD
player
with
the
RI
‘mark.
>
:
Press
this
button
to
play
the
CD
player.
a
:
Press
this
button
to
pause
the
CD.
play
back.
To
resume
disc
play,
press
the
PLAY
button.
DISC:
Press
to
use
for
sequential
selection
-of
discs
in
the
order
they
were
loaded
on
the
CD
change:
(RC-183S.
only)
:
Press
this
button
to
ap
the
cD
player.
t¢<:
Press
this
button:
to
ge
back
to
the
:
beginning.
of
the
current
track:and.-
again
to
=e
Been
Bs
the
ptevious
;
track.
rege
ty
‘pp:
Press
this
button
to
se
to:
the
next
track.
»:
Lhe
fb
Audio
Muting
Button
Aveo
MUTE)
and
Indicator
This
button
temporarily
nies
off
the
sound
from
the
speaker
or
headphone.
Pressing
this
button
will
operate
the
TX-902
audio
muting
circuit.
The
audio
muting
indicator
“AUDIO
MUTE”
will
flash.
Pressing
the
button
again
or
using
the
POWER
button
on
the
remote
control
transmitter
to
turn
the
power
on
will
turn
off
the
audio
muting.
@
The
tuner
amplifiers
are
provided
with
the
following
remote
control
transmitters:
eo
USA and Canadian models..
other area models F
RC-183S
_ RC-184S
Input Selector Buttons (TAPE-1,
“TUNER, PHONO, CD, TAPE-2) [9]
= 4% When the TUNER ‘button is pressed, the
© station which was received previously is
recalled. Selection of AM or FM should be
done on the main unit.
~ Tape Operation Buttons
(DECK-A, DECK-B)
These buttons contro! Onkyo double cassette
tape decks that can be remote controlled. Use
the DECK-B buttons to control single cassette
tape decks with the Ri mark.
oyu: When this is pressed, the recording
-stand+by: mode is entered.
4 : The tape plays, moving from right
:
to
left;
or,
inthe
recording
stand-by
mode, recording begins.
@ : Interrupts. all operations: ©
> : The-tape plays,;moving from left to
. tight, or, in.the recording, stand-by
mode, recording begins. :
oo Fast forward from.right. to: left.
>>
,:
Fast
forward.
from.
left,to
right.
Tuner Operation Buttons (TUNER) {11]
CLASS: Class selector button, ae
4 PRESET > : Preset memory, DOWN/UP
buttons”
Volume Buttons (UP, DOWN)
Using
the
remote
control
transmitter
4.
Remove
the
batteries
if
the
remote
control
transmitter
is
not
going
to
be
used
for
a
long
time.
2.
The
batteries
of
the
remote
control
transmitter
must
be
replaced
periodically.
3.
This
unit
uses
infrared
rays.
Therefore,
commands
may
not
be
received
properly
if
the
front
panel
of
this
unit
is
exposed
to
bright
light.
To
prevent
this
from
occurring,
place
this
unit
so
that
it
is
not
directly
exposed
to
bright
light.
4.
If
this
unit
is
placed
inside
an
audio
rack
behind
a
glass
door,
the
door
should
not
have
colored
glass
or
have
any
decorations
on
it,
since
this
could
shorten
the
range
or
prevent
commands
from
being
received.
5.
Use
of
other
infrared
remote
control
devices
in
the
same
room
may
cause
interference.
6.
The
transmitter
operates
up
to
a
distance
of
about
five
meters
(16
feet).
The
transmitting
window
must
always
be
pointed
at
the
reception
window
when
a
command
is
sent
to
the
TX-902.
7.
if
this
remote
control
transmitter
does
not
operate
properly,
confirm
that
the
batteries
are
not
dead.
If
the
problem
persists,
contact
your
Onkyo
Service
Center.
Remote sensor
approx. 5m
(16 feet)
Remote control transmitter