Onkyo TX-930 - Remote Control Transmitter; Transmitter Button Functions and Layout; Sleep Timer and Usage Tips

Remote control transmitter
Power Button (POWER)
Input Selector Buttons (TAPE-1, |
TUNER, PHONO, CD, TAPE-2) [9]
When the TUNER button is pressed, the
station which was received previously is
recalled. Selection of AM or FM should be
done on the main unit.
CD Operation Buttons (CD)
These buttons are used to operate an Onkyo
CD player with the FRE mark.
> - Press this button to play the CD
player.
TT - Press this button to pause the CD
play back. To resume disc play,
—
Sleep button (SLEEP)
Press to set the power off timer. The sleep timer is a function
which button off the power to the system from the time it is
set.When this button is pressed, “90 MIN" is displayed for 5
seconds, and the power goes off 90 minutes later.Each time the
button is pressed during 5 seconds, the timer setting changes,
by 10 minute intervals, such as 80, 70, 60.... While the sleep
timer is operating, the SLEEP | indicator is lighted. If the sieep
button is pressed during this time, the amount of time remaining
on the sieep timer is displayed, and if the button is pressed
during
that
display,
10
minutes
will
be
subtracted
from
that
time.
lf the button is pressed when the panel display shows 10
minutes or less,the sleep timer is cancelled, and the power is
not turned off.
a Tape Operation Buttons
(DECK-A, DECK-B)
These buttons control Onkyo double cassette
tape decks that can be remote controlled.
Use the DECK-B buttons to control single
1 cassette tape decks with the FRE mark.
@ /Il: When this is pressed, the recording
press the PLAY button.
DISC : Press to use for sequential selection
of discs in the order they were :
loaded on the CD changer.
stand-by mode Is entered.
< - The tape plays, moving from right to left,
or, in the recording stand-by mode, re-
cording begins.
a
:
Press
this
button
to
stop
the
CD
a
Interrupts
all
operations.
player.
“™
oe
>
‘The
tape
plays,
moving
from
left
to
It:
Press
this
button
to
go
back
to
the
QC
=
=)
om
right,
or,
in
the
recording
stand-by
beginning
of
the
current
track
and
co
TUNER
mode,
recording
begins.
again
to
skip
back
to
the
previous
LJ
@<4
=
Fast
forward
from
right
to
left.
track.
me
—
Fast
forward
from
left
to
right.
Pei
Press
this
button
to
skip
to
the
next
track.
Audio Muting Button (AUDIO MUTE)
This button temporarily switches off the
sound from the speaker or headphone.
Pressing this button will operate the
TX-930/910 audio muting circuit. The audio
muting indicator “AUDIO MUTE” will flash.
Pressing the button again or using the
POWER button on the remote control
transmitter to turn the power on will turn off
the audio muting.
Tuner Operation Buttons (TUNER) [11]
CLASS: Class selector button
«= PRESET » : Preset memory DOWN/UP
buttons
Volume Buttons (UP, DOWN)
pL
Using the remote control transmitter
1. Remove the batteries if the remote control transmitter is not going
to be used for a long time.
2. The batteries of the remote control transmitter must be replaced
periodically.
3. This unit uses infrared rays. Therefore, commands may not be
received properly if the front panel of this unit is exposed to bright
light. To prevent this from occurring, place this unit so that it is not
directly exposed to bright light.
4. If this unit is placed inside an audio rack behind a glass door, the
door should not have colored glass or have any decorations on it,
since this could shorten the range or prevent commands from being
received.
5. Use of other infrared remote control devices in the same room may
cause interference.
6. The transmitter operates up to a distance of about five meters (16
feet). The transmitting window must always be pointed at the
reception window when a command is sent to the TX-930/910.
7. Ifthis remote control transmitter does not operate properly, confirm
that the batteries are not dead. |f the probiem persists, contact your
Onkyo Service Center.
TX-930/910
Remote sensor
| approx. 5m
va (16 feet)
Remote control transmitter