Advanced Operations
En-75
■ Operating on the AV receiver
Tip
• The Whole House Mode function shares the input source of
main room with Multi Zone (➔ page 50).
■ Operating on the remote controller
To control Zone 2/3, you must press ZONE2 or
ZONE3 on the remote controller first.
Adjusting the Volume for Zone 2
■ Operating on the remote controller
■ Operating on the AV receiver
If your Zone 2 speakers are connected to a receiver
or integrated amplifier in Zone 2, use its volume
control to adjust the volume.
Muting Zone 2
■ Operating on the remote controller
Tip
• To unmute, press ZONE2 followed by MUTING again.
Zone can also be unmuted by adjusting the volume.
Note
• Only analog, NET or USB input source is output from the
ZONE 2/ZONE 3 LINE OUT jacks and ZONE 2 L/R
terminals.
• You cannot select different AM or FM radio stations for your
main room and Zone 2/3. The same AM/FM radio station
will be heard in each room. Namely, if you have selected an
FM station for the main room, that station will also be output
in Zone 2/3.
• You cannot select different input selector NET or USB for
your main room and Zone 2/3. Namely, if you have selected
USB input selector for Zone 2/3, USB input selector will be
selected in main room even if NET has been selected for
main room.
• BLUETOOTH cannot be selected as input selector in Multi
Zone. If you play audio from Bluetooth-enabled device in
Multi Zone, select “Z2 Sel: Source” or “Z3 Sel: Source”,
and BLUETOOTH as input selector in Main room.
• When Zone 2/3 is activated and its input selector is
selected, the power consumption of standby mode slightly
increases.
• While Zone 2/3 is on, u functions will not work.
• When setting the AV receiver to standby mode while Zone
2/3 is active, the Z2 or Z3 indicator is dimly lit.
• Activating Zones in the main room when the listening mode
is set to Pure Audio (European, Australian and Asian
models) will automatically switch it to Direct.
•“AUX” cannot be selected as input sources for Zone 2/3.
• When “AUX” is the input source of Main room and Zone 2/3
is set to share the same source, no sound will be output
from Zone 2/3.
Controlling Multi Zone Components
1
To turn on Zone 2/3 and select an input source,
press ZONE 2 or ZONE 3 followed by an input
selector button within 8 seconds.
Zone 2/3 turns on, the Z2 or Z3 indicator lights on
the AV receiver’s display.
To select the same source as the main room’s,
press ZONE 2 or ZONE 3 twice. “Z2 Sel:
Source” or “Z3 Sel: Source” appears on the AV
receiver’s display.
2
To turn off Zone 2/3, press ZONE 2 or ZONE 3
followed by 8ON/STANDBY within 8 seconds.
The zone is turned off.
ZONE 2 ZONE 3 MASTER VOLUME
8ON/STANDBY
Input selector buttons
1
Press ZONE2 or ZONE3, then point the remote
controller at the AV receiver and press
8RECEIVER.
Zone 2/3 turns on, the Z2 or Z3 indicator lights on
the AV receiver’s display.
2
To select an input source for Zone 2/3, press
ZONE2 or ZONE3, followed by an INPUT
SELECTOR button.
3
To turn off Zone 2/3, press ZONE2 or ZONE3,
followed by 8RECEIVER.
The zone is turned off.
1
Press ZONE2.
2
Use VOL q/w.
1
Press ZONE 2 (the Z2 indicator on the AV
receiver’s display flashes).
2
Use MASTER VOLUME control within 8
seconds.
8RECEIVER
ZONE2
ZONE3
INPUT
SELECTOR
VOLq/w
MUTING
1
Press ZONE2 followed by MUTING.
To Next Page
Loading...
