Listening Modes
TX-SR701/701E
Listening mode buttons
MODE
Listening mode
S buttons
Selecting a listening mode (TX-SR701/701E)
• Refer to pages 46, 47 for lnore details of listening nlodes.
• Refer to page 54 for sources and lislening modes.
• When playing Dolby Digital or DTS software, the listening
mode will automa/ically change to Dolby Digital or DTS.
Tip:
You can set in advance a different listening mode for each input
source. For more details, see page 54.
When using the remote controller, first press the RCVR
MODE button before preceding to the step below.
Press one of the listening mode buttons to select the listening mode.
TX-SR701/701 E ......... 2_;2;_,_,_,_
D_ECT
©
Remote controller
DIRECT/PURE AUDIO (DIRECT, PURE A): Changes the
listening mode for the signal type that is currently being input from
the selected input source to the Direct listening mode. If pressed,
the corresponding settings in the "Input Setup" menu for the
selected input source is also changed. When the listening mode is
set to Direct, you can switch between Direct and Pure Audio. When
you select Pure Audio, the video signal is inlerrupled (resulting in a
blacked-out screen), and the PURE AUDIO indicator lights up.
Note:
In the Pure Audio mode, if any component video signal is presented
on the COMPONENT VIDEO INPUT2,jack, it will be output to the
COMPONENT OUTPUT ,jack.
STERE(): Changes the listening mode for the signal type that is
currently being input from the selected input source to the Stereo
listening mode. If pressed, the corresponding settings in the "Input
Setup" menu for the selected input source is also changed (see page
54).
SURROUND (SURR): Changes the lislening mode for the signal
type that is currently being input from the selecled input source to
the surround mode thai malches the signal type (e.g., Dolby Pro
Logic II, Dolby Digital, DTS, or DTS Neo:6). If pressed, the
corresponding sellings in the "Input Setup" menu for the selected
input source is also changed (see page 54).
If |he SURROUND button is pre_ed
• While playing back DTS sources
Each time you press the button, the DTS-ES setting switches
from: Auto --_ On --_ Off.
Auto: When a DTS source with a DTS-ES flag (ID signal for
DTS-ES) is input, the lis/ening mode changes automatically to
DTS-ES Discrete 6.1 or DTS-ES Matrix 6.1. If the DTS source
has no DTS-ES flag, the source is played in DTS mode.
On: When a DTS source with a DTS-ES flag is input, the
lis/ening mode changes automatically to DTS-ES Discrete 6.1
or DTS-ES Ma/rix 6.1. if the DTS source has no DTS-ES flag,
the source is played in DTS-ES Matrix 6.1.
Off: DTS sources are always played in the DTS mode. The
DTS-ES modes are not used even when the DTS source has the
DTS-ES flag.
• While playing back Dolby Digital (Multichannel) sources
Select whether or not to play back Dolby Digital sources using
the ma/rix 6.l-channel decoder when using surround back
speakers.
Each time you press the button, the Dolby Digital EX setting
swilches from: Auto --+ On --_ Off.
Auto: Sources with an EX flag (ID signal for Dolby Digital) are
automa/ically played back in Dolby Digital EX. If the source
has no EX flag, the source is played back in Dolby Digital.
On: When a Dolby Digital source with an EX flag is input, the
lis/ening mode changes automatically 1o Dolby Digital EX. If
the Dolby Digital source has no EX flag, the source is played in
the Dolby Digital EX.
Off: Dolby Digital EX playback is not performed even if an EX
flag exists. (Playback is the normal Dolby Digital playback.)
Be aware that if the surround channel is monaural or there is no
surround channel, the source is played back in Dolby Digital
regardless of this selling.
• While playing back Analog/PCM sources or Dolby Digital 2-
channel sources
Each time you press the button, the Dolby Digital setting
swilches from: Pro Logic II Movie --+ Pro Logic 11 Music --+
DTS Neo6:Cinema --_ DTS Neo6:Music.
If "None" is selected for the surround speaker setting in the
"Speaker Config" menu, DTS Neo:6 Music will not appear.
48
To Next Page
Loading...
