How to fix “flare-ups” or grease fires on my Onward Grill?
To fix flare-ups or grease fires on your Onward Grill: * Address excessive grease buildup by thoroughly scraping off the Flav-R-Wave and the inside of the cookbox, then vacuum out any debris. * Reduce excessive heat by turning the burner controls to a lower setting.
Why is my Onward 24025-913 Grill flame flickering or temperatures low?
The excess flow safety device in the connection between the cylinder and the barbecue may have been activated. To resolve this, turn the LP cylinder valve off, then turn all burners to the OFF position. Disconnect the regulator from the cylinder and wait two minutes. Re-attach the regulator to the cylinder, open the cylinder valve slowly, and wait one minute. Then, light the grill.
How to fix an Onward 24025-913 Grill ignitor that is not working?
If the ignitor on your Onward Grill isn't working, try these solutions: * **Dead battery:** Replace the ignitor battery. * **Disconnected wires:** Ensure the main burner and side burner electrode wires are all connected. * **Misaligned electrode:** Realign the electrode on the burner and clear any debris from the area. * **Ignitor malfunction:** Use the Match Lighting procedure.
What to do if I hear a regulator humming noise on my Onward 24025-913?
If you hear a humming noise from the regulator on your Onward Grill, it's likely because the cylinder valve was opened too quickly. Try opening the cylinder valve more slowly.
Why does my Onward Grill have hot spots on the cooking surface?
Hot spots on the cooking surface of your Onward Grill can be caused by: * A blocked venturi: Remove the burner and clean the venturi. * Debris buildup on the Flav-R-Wave: Scrape off the Flav-R-Wave and vacuum.
What causes decreasing heat and a popping sound on my Onward 24025-913?
Decreasing heat and a popping sound on your Onward Grill can be due to: * Being out of LP Gas: Refill your LP Gas Cylinder. * A blocked venturi: Remove the burner and clean the venturi.
What to do if my Onward Grill has a leak?
If you detect a leak at the cylinder, regulator, or other connection on your Onward Grill: * If the regulator fitting is loose, tighten the fitting and perform a leak test. * If there's a gas leak in the hose/regulator or control valves, seek assistance from an authorized service center.
Why is there a yellow flame on my Onward Grill?
Some yellow flame is normal on an Onward Grill. However, if it is excessive: * The venturi may be blocked: remove the burner and clean the venturi. * Burner ports may be blocked: remove the burner and clean with a soft bristle brush (e.g., toothbrush).
What causes flames beneath the control panel of my Onward 24025-913 Grill?
Flames beneath the control panel (flashback fire) on your Onward Grill can be caused by a blocked venturi. Remove the burner and clean the venturi.
What to do if the inside of my Onward 24025-913 Grill lid appears to be peeling?
The apparent peeling inside the lid of your Onward Grill is actually a build-up of grease. The inside of the lid is not painted and cannot peel. Clean it with a stiff bristle brush or scraper.
Guidelines for safe handling, storage, and use of gas cylinders to prevent damage and leaks.
Step-by-step guide for safely connecting and disconnecting butane gas cylinders, including screw-on and switch-on types.
Detailed instructions for connecting and disconnecting propane gas cylinders, emphasizing proper thread and sealing.
Instructions for lighting the side burner using either the ignitor or a match.
Guidance on how to light the rear rotisserie burner, with a warning about main burner use.
Steps for lighting the main burner using the ignitor or a match, including safety timeframes.
To Next Page
General
