EasyManuals Logo

Onyx 245 User Manual

Onyx 245
8 pages
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #8 background imageLoading...
Page #8 background image
8
COOLING FAN
A built-in cooling fan helps to keep the charger cool during operation. This will help extend the service life of the charger,
and allow it to function more accurately and effi ciently. CAUTION: Do not block the vent holes for the cooling fan on
the left side of the charger as this could cause the charger to overheat and possibly cause permanent damage.
ERROR MESSAGES AND TROUBLESHOOTING GUIDE
Several safety features are included in this charger to protect itself and the battery against certain unwanted conditions,
as follows:
LCD MESSAGE PROBLEM AND SOLUTION
“Err.1” The DC input voltage is below 11.0V or exceeds 15V DC. Make sure the input voltage is within this range.
“Err.2” A battery is not connected to the output. Make sure a good connection exists between the battery and charger
and re-try.
“Err.3” The battery is connected backwards to the output. Re-connect the battery to the charger’s output with the proper
polarity.
“Err.4” The battery has become disconnected during charge. Re-establish a good physical connection between the
battery and charger, and re-start charge.
“Err.5” Some type of electronic interruption or malfunction has occurred. If you believe that some external force might have
caused the charger to err, and that a true circuit malfunction has not occurred, you might attempt a re-start charge.
Otherwise, if you believe the charger is not functioning properly, disconnect the battery from the charger, and the
charger from the input power, and contact Hobby Services for further details.
“Err.6” The charger has somehow fallen out of calibration. Contact Hobby Services for further details.
“Err.7” Li-xx Bat Low and Hi voltage error. When pack voltage of the connected lithium battery is not certain.
“Err.8” Balance voltage error. When charging Li-xx with the balance cable connected to the charger, if balance cell voltage
is more or less than acceptable voltage of each battery, this error should occur.
“STOP” The 90-minute backup safety timer has expired. You can re-start charge or disconnect the battery from the charger.
5-YEAR LIMITED WARRANTY - *U.S.A. and CANADA ONLY
DuraTrax warrants this product to be free from defects in materials and workmanship for a period of fi ve (5) years from
the date of purchase. During that period, DuraTrax will, at its option, repair or replace without service charge any product
deemed defective due to those causes. You will be required to provide proof of purchase (invoice or receipt). This warranty
does not cover damage caused by abuse, misuse, alteration or accident. If there is damage stemming from these causes
within the stated warranty period, DuraTrax will, at its option, repair or replace it for a service charge not greater than 50%
of its then current retail list price. Be sure to include your daytime telephone number in case we need to contact you about
your repair. This warranty gives you specifi c rights. You may also have other rights, which vary from state to state.
For service on your DuraTrax product, warranty or non-warranty, send it post-paid and insured to:
HOBBY SERVICES (217) 398-0007 hobbyservices@hobbico.com
3002 N. Apollo Drive Suite 1 duratrax.com
Champaign, IL 61822
*For warranty and service information if purchased outside the USA or Canada, see the additional warranty information
insert (if applicable) or ask your retailer for more information.
© 2012 Hobbico
®
Inc. All rights reserved. Made in China DTXP4245 v2

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Onyx 245 and is the answer not in the manual?

Onyx 245 Specifications

General IconGeneral
BrandOnyx
Model245
CategoryBattery Charger
LanguageEnglish

Related product manuals