Optex iVISION+ IVP-GU - User Manual

IVP-GU(G) features
“OPEN DOOR” Relay Output Function
AC/DC (10~24V) Adaptable
Chime On-Off Mode
* Relay Output function must meet other requirements dependent on the third party equipment.
OPTEX will not be held responsible for any damage or injuries caused due to using this function.
IVP-GU(G)
(Gateway Chime Unit)
Installation Instructions
Wireless Video Intercom
IMPORTANT NOTICE
1.
Operations under harsh environments such as out of warranted temperature,
rapid temperature change, high humidity, constant moisturization may cause the
unit to malfunction.
Electronic device such as TVs, Radios, PCs, Microwave ovens or any other device
with an electric motor may cause the unit to malfunction.
Impact or shocks can cause severe damage to the unit. Please handle the unit
with care and operate without exerting strong forces.
Transmission range of communication between units may decrease under
the following conditions.
- Any unit is installed on a metal surface.
- Presence of reinforced concrete, steel doors or other metal construction
materials between units.
- Places near strong radio sources such as broadcast stations or substations.
While installing/using a Gateway Chime Unit
- Do not install/use in damp, steamy or dusty environments.
- Do not hold the Gateway Chime Unit to your ear - your hearing could be damaged.
- Do not install in an unstable location or where subject to strong vibration.
PARTS IDENTIFICATION
3.
CHOOSING LOCATION
2.
If there is a pre-existing door bell inside the house, a Gateway Chime Unit (IVP-GU)
may be capable of adapting the pre-existing power wires (AC/DC 10-24V 3 Wmax).
IVP-GU should be located in a place where the unit has a clear signal reception
and transmission availability.
The performance of a IVP-GU is dependent on the transmission environment of radio
signals from locations of connecting units. A communication range will be significantly
reduced by more number and thickness of walls which the signal is required to pass.
For iVISION+ system, maximum communication range is around 300ft (100m)
in an open air environment. Following materials may decrease the maximum
communication range and may potentially cause loss of transmission signals.
• Metal barricades such as metal doors and shutters.
• Walls with aluminium foil insulation.
• Concrete or galvanized metal walls.
Gateway Chime Unit uses 2.4GHz radio frequency for iVISION+ system.
The Gateway Chime Unit needs to be powered from an AC/DC 10-24V 3W(max)
power source. An open ended third party power adapter may be available from
local electronics stores. Power input has no polarity. Please make sure to tighten
terminal screws to avoid loose ends.
If applicable, configure all pairing setup and carry out feasibility study before
mounting on a wall.
Speaker
LED Indicator
Gateway Chime Unit (Front)
POWERING THE UNIT
4.
ATTENTION:
Thank you for purchasing the iVISION+ wireless video intercom.
Before installation and usage, please read this instruction manual thoroughly
and keep this safe for future reference.
Mounting Screw
Gateway Chime Unit (Back)
Power input
Relay output
Pairing button A& B
Chime ON/OFF switch
Fixing Screw
Mounting Plate
INSTALLATION
5.
For the optimal radio performance, mount IVP-GUs high on a wall and in an open area avoiding a metal surface and surrounding.
(1) Fix a Mounting Plate on a feasible location (2) Run a power cable to the location
and connect to the Power input.
If applicable, also run a relay connection
from the Relay output to the third
party equipment.
(3) Slide the IVP-GU onto
the Mounting Plate and
tighten the Fixing Screw
at the bottom.
One iVISION+ system can host up to 2 units of Gateway Chime Unit (IVP-GU).
N.C.
COM
N.O.
AC/DC
10-24V
Relayoutput
Powerinput
Mounting Screw
toPowerinput
toRelayoutput
21mm/0.83”
Tightenascrew
Slideon
toapowersource
toathirdparty
equipment
If “OPEN DOOR” Relay Output function is used, please carefully choose a location for each of IVP-GU to secure a physicalaccess to the IVP-GU.
Mounting Plate
(optional)

Summary

Important Notice

Operational Precautions and Warnings

Covers harsh environments, electronic interference, physical impact, transmission range limits, and usage guidelines.

Choosing Location

Location Selection Criteria

Guidance on selecting an optimal location for signal reception and transmission, considering environmental factors.

Parts Identification

Powering the Unit

Power Source Requirements

Details the required AC/DC power input, voltage, and wattage specifications for the unit.

Installation

Mounting and Connection Procedure

Step-by-step guide for physically mounting the unit and connecting power and relay outputs.

Pairing with Other iVISION+ Devices

Pairing Procedure Steps

Outlines the process for pairing the Gateway Chime Unit with other iVISION+ system devices.

Additional Setting

Chime Volume Adjustment

Instructions on how to adjust the chime volume levels and turn the chime sound on/off.

Specification

Dimensions

Provides the physical size measurements of the Gateway Chime Unit.

Specification Table

Lists technical specifications including operating temperature, humidity, frequency, and power ratings.

Warranty

Warranty Terms and Conditions

Details the product warranty period, coverage, and exclusions.

Optex iVISION+ IVP-GU Specifications

General

Type	Wireless Video Intercom System
Wireless Range	100 meters (line of sight)
Camera	Built-in
Night Vision	Yes (IR LEDs)
Audio	Two-way
Operating Temperature	-10°C to +50°C
Power Supply	AC Adapter or Rechargeable Battery
Housing	Weather-resistant
Power Source (Door Station)	12V DC
Power Source (Handheld Unit)	Rechargeable Lithium-ion battery