Oreck Rinse-A-Matic Steemer Ultra M800 Series User Manual (English)

Questions and Answers:

M
Michael AndersonJul 30, 2025
How to fix Oreck Rinse-A-Matic Steemer Ultra M800 not dispensing water and cleaning solution?
- M
  Michael HuffmanJul 30, 2025
  If the Oreck Vacuum Cleaner isn't dispensing water and cleaning solution, ensure the upper supply tank is partially filled with hot tap water, without overfilling. Check that a cleaner cartridge is installed and the white lever is locked down, replacing an empty cartridge if necessary. Also, verify the spray tips aren't clogged and clean them with a towel or damp cloth. For above-the-floor cleaning, confirm the hand-held nozzle and hose are properly connected and the nozzle change button is engaged.
B
Brendan HammondAug 4, 2025
Why my Oreck Rinse-A-Matic Steemer Ultra M800 will not run or suddenly stops?
- J
  Jonathon ReynoldsAug 4, 2025
  If your Oreck Vacuum Cleaner won't run or suddenly stops, first check if the plug has slipped out of the outlet and reinsert it. If that's not the issue, the A.L.C.I. may have tripped due to current fluctuations. Press the reset button to restart the unit.
C
catherinescottAug 8, 2025
What to do if Oreck Rinse-A-Matic Steemer Ultra M800 Vacuum Cleaner is not removing certain stains?
- P
  Philip CooperAug 9, 2025
  To remove certain stains and heavy traffic area spots with your Oreck Vacuum Cleaner, consider using a stain pretreatment like Steemer Full Release® Professional Spot & Stain PreCleaner to loosen grease, oil, and food stains. Also, make several slow passes over the stain from different angles to improve stain removal.
N
nmooneyAug 14, 2025
Why is my carpet excessively wet after cleaning with Oreck Vacuum Cleaner?
- J
  Jessica BrownAug 14, 2025
  If your carpet is excessively wet after cleaning with the Oreck Vacuum Cleaner, make at least one additional pass over the wet carpet without pressing the spray button. Ensure the hand-held nozzle trigger isn't engaged. Slowly pull the unit toward you to extract remaining liquid, and gently push the nozzle deep into the carpet pile to speed drying. Check for airpath obstructions in the hose, cleaner neck, and nozzle, and ensure the inlet screen is free of debris.
I
irosalesAug 18, 2025
What to do if Oreck Rinse-A-Matic Steemer Ultra M800 Steemer brush roll will not turn?
- A
  Andrea BishopAug 18, 2025
  If the Steemer brush roll of your Oreck Vacuum Cleaner won't turn, check that the nozzle power cord is completely connected to the main unit. Inspect the brush roll for obstructions and ensure it can turn freely. Also, make sure the belt is in good working order and replace it if needed. If the belt and brush roll are excessively wet, run the unit on a dry section of carpet briefly to resolve momentary slippage.
A
allenkennethAug 25, 2025
How to prevent dark streaks on carpet after using Oreck Rinse-A-Matic Steemer Ultra M800?
- J
  John RosalesAug 25, 2025
  If you notice dark streaks on the carpet after cleaning with your Oreck Vacuum Cleaner, operate the machine more slowly, as one slow pass yields better results than several fast strokes. Overlap each pass for maximum cleaning without streaking. For heavily soiled carpets, allow the carpet to dry and repeat the process as needed.

Oreck Rinse-A-Matic Steemer Ultra M800 Series Specifications

General

Model	Rinse-A-Matic Steemer Ultra M800 Series
Category	Vacuum Cleaner
Type	Carpet Cleaner
Power Source	Corded Electric
Voltage	120V
Amps	12A
Watts	1440W
Tank Capacity	1 gallon
Hose Length	6 feet
Cord Length	25 feet
Included Tools	Upholstery tool, Crevice tool
Features	Heated cleaning