3
•
Note on connecting a power supply whose positive terminal is
grounded
The data edit connector (CN3), I/O signal connectors (CN5/CN6) and
RS-485 communication connectors (CN7/CN8) on the driver are not
electrically insulated. When grounding the positive terminal of the power
supply, do not connect any equipment (PC, etc.) whose negative terminal
is grounded. Doing so may cause the driver and this equipment to short,
damaging both.
•
Use a connection cable (supplied or accessory) when extending the
wiring distance between the motor and driver
•
When using the motor in operation such as vertical drive
(gravitational operation) or a large inertial load drive, use an
accessory regeneration unit (sold separately).
The driver may be damaged if the regeneration energy generated during
vertical drive (gravitational operation) or sudden starting/stopping of a large
inertial load exceeds the allowable limit that can be absorbed by the driver.
The accessory regeneration unit (sold separately) is designed to discharge the
regenerated energy, thereby protecting the driver.
•
Saving data to the non-volatile memory
Do not turn o the 24 VDC power supply while writing the data to the
non-volatile memory, and also do not turn o within 5 seconds after the
completion of writing the data. Doing so may abort writing the data and cause
an EEPROM error alarm to generate.
The non-volatile memory can be rewritten approximately 100,000 times.
Preparation
Checking the product
Verify that the items listed below are included. Report any missing or
damaged items to the branch or sales oce from which you purchased the
product.
•
Motor ......................................................... 1 unit
(With a gearhead, only for combination type)
•
Driver ........................................................ 1 unit
•
Connection cable ....................................... 1 piece
(Only models with a supplied connection cable)
•
CN5 connector (10 pins) ........................... 1 piece
•
CN6 connector (8 pins) ............................. 1 piece
•
External potentiometer .............................. 1 piece
•
Signal cable for external potentiometer .... 1 piece [1 m (3.3 ft.)]
•
OPERATING MANUAL .......................... 1 copy (this document)
Accessories for combination type
•
Hexagonal socket head screw set .............. 1 set
•
Parallel key ................................................ 1 piece
•
Safety cover ............................................... 1 piece
(Supplied with the hollow shaft at gearhead)
•
Safety cover mounting screw .................... 2 pieces
(Supplied with the hollow shaft at gearhead)
Combinations of motors and drivers
Verify the model number of the purchased product against the number shown
on the package label. Check the model number of the motor and driver
against the number shown on the nameplate.
•
o
in the model names indicates a number representing the gear ratio.
•
•
indicates a number representing the length of a connection cable.
•
The combination types come with the motor and gearhead pre-assembled.
•z
Standard type
•
Combination type • parallel shaft gearhead
Model Motor model
Gearhead
model
Driver model
BLE23AR
o
S-
BLEM23-GFS GFS2G
o
BLED3AM-R
BLE23CR
o
S-
BLED3CM-R
BLE46AR
o
S-
BLEM46-GFS GFS4G
o
BLED6AM-R
BLE46CR
o
S-
BLED6CM-R
BLE512AR
o
S-
BLEM512-GFS GFS5G
o
BLED12AM-R
BLE512CR
o
S-
BLED12CM-R
•
Combination type • hollow shaft at gearhead
Model Motor model
Gearhead
model
Driver model
BLE23AR
o
F-
BLEM23-GFS GFS2G
o
FR
BLED3AM-R
BLE23CR
o
F-
BLED3CM-R
BLE46AR
o
F-
BLEM46-GFS GFS4G
o
FR
BLED6AM-R
BLE46CR
o
F-
BLED6CM-R
BLE512AR
o
F-
BLEM512-GFS GFS5G
o
FR
BLED12AM-R
BLE512CR
o
F-
BLED12CM-R
•
Round shaft type
Model Motor model Driver model
BLE23ARA-
BLEM23-A
BLED3AM-R
BLE23CRA-
BLED3CM-R
BLE46ARA-
BLEM46-A
BLED6AM-R
BLE46CRA-
BLED6CM-R
BLE512ARA-
BLEM512-A
BLED12AM-R
BLE512CRA-
BLED12CM-R
•z
Electromagnetic brake type
•
Combination type • parallel shaft gearhead
Model Motor model
Gearhead
model
Driver model
BLE23AMR
o
S-
BLEM23M2-GFS GFS2G
o
BLED3AM-R
BLE23CMR
o
S-
BLED3CM-R
BLE46AMR
o
S-
BLEM46M2-GFS GFS4G
o
BLED6AM-R
BLE46CMR
o
S-
BLED6CM-R
BLE512AMR
o
S-
BLEM512M2-GFS GFS5G
o
BLED12AM-R
BLE512CMR
o
S-
BLED12CM-R
•
Combination type • hollow shaft at gearhead
Model Motor model
Gearhead
model
Driver model
BLE23AMR
o
F-
BLEM23M2-GFS GFS2G
o
FR
BLED3AM-R
BLE23CMR
o
F-
BLED3CM-R
BLE46AMR
o
F-
BLEM46M2-GFS GFS4G
o
FR
BLED6AM-R
BLE46CMR
o
F-
BLED6CM-R
BLE512AMR
o
F-
BLEM512M2-GFS GFS5G
o
FR
BLED12AM-R
BLE512CMR
o
F-
BLED12CM-R
•
Round shaft type
Model Motor model Driver model
BLE23AMRA-
BLEM23M2-A
BLED3AM-R
BLE23CMRA-
BLED3CM-R
BLE46AMRA-
BLEM46M2-A
BLED6AM-R
BLE46CMRA-
BLED6CM-R
BLE512AMRA-
BLEM512M2-A
BLED12AM-R
BLE512CMRA-
BLED12CM-R
To Next Page
Loading...
