Oriental motor BLH2D50-K - User Manual

HP-5072-2
Brushless Motor
BLH
Series
Analog Setting Type
OPERATING MANUAL
Thank you for purchasing an Oriental Motor product.
This Operating Manual describes product handling procedures and safety precautions.
•
Please read it thoroughly to ensure safe operation.
•
Always keep the manual where it is readily available.
Table of contents
1 Introduction ..........................................................2
2 Safety precautions ..............................................3
3 Precautions for use .............................................4
4 Preparation ............................................................5
4.1 Checking the product .............................................. 5
4.2 How to identify the product model.................... 5
4.3 Information about nameplate .............................. 5
4.4 Products possible to combine .............................. 5
4.5 Names and functions of parts .............................. 6
5 Installation .............................................................7
5.1 Installation location .................................................. 7
5.2 Installing the driver .................................................. 7
6 Connection ............................................................8
6.1 Connecting the motor and driver (CN3) ........... 8
6.2 Connecting the power supply (CN1).................. 8
6.3 Grounding ................................................................... 9
6.4 Connecting the I/O signals (CN2) ........................ 9
6.5 Driver I/O circuit .......................................................10
6.6 Connecting external analog setting
devices ........................................................................10
6.7 Connection diagram ..............................................11
6.8 Noise measures ........................................................ 12
6.9 Conformity to the EMC Directive .......................12
7 Operation ............................................................ 14
7.1 Setting the rotation speed ...................................14
7.2 Setting the acceleration time and
deceleration time ....................................................15
7.3 Operation and stop ................................................15
7.4 Rotation direction of the motor output
shaft .............................................................................16
7.5 Multi-motor control ................................................17
8 Maintenance and inspection ....................... 18
8.1 Inspection ..................................................................18
8.2 Warranty .....................................................................18
8.3 Disposal ......................................................................18
9 Troubleshooting ............................................... 19
10 Alarms ................................................................... 20
10.1 Alarm reset ................................................................20
10.2 Alarm lists ...................................................................21
11 Specications ..................................................... 22
11.1 Specications ............................................................22
11.2 General specications ...........................................22
11.3 Dimension..................................................................22
12 Regulations and standards ........................... 23
12.1 UL Standards and CSA Standards ......................23
12.2 EU Directives .............................................................23
12.3 Republic of Korea, Radio Waves Act .................23
12.4 RoHS Directive ..........................................................23

Summary

Introduction

Before using the product

Crucial precautions for safe and correct operation before initial use.

Safety precautions

WARNING

Identifies hazards that may cause serious injury or death if instructions are not followed.

CAUTION

Highlights hazards that may cause injury or property damage if instructions are not followed.

Precautions for use

Do not perform gravitational operation (vertical drive)

Warning against vertical operation due to potential load drop and uncontrolled speed.

Do not conduct insulation resistance or dielectric strength tests with connected motor;driver

Warning against performing electrical tests with the motor and driver connected.

Preparation

4.1 Checking the product

4.2 How to identify the product model

4.4 Products possible to combine

4.5 Names and functions of parts

Identifies and describes the purpose of each component on the driver.

Installation

5.1 Installation location

Specifies suitable environmental conditions and locations for installing the driver.

5.2 Installing the driver

Provides instructions on how to physically mount and install the driver.

Connection

6.1 Connecting the motor and driver (CN3)

Details the procedure for connecting the motor cable to the driver's CN3 connector.

6.2 Connecting the power supply (CN1)

Explains how to connect the power supply cable to the driver's CN1 connector.

6.3 Grounding

Instructions for proper grounding of the motor and driver for safety.

6.4 Connecting the I;O signals (CN2)

Describes how to connect the I/O signal cables to the driver's CN2 connector.

6.6 Connecting external analog setting devices

Using external DC voltage for speed setting

6.7 Connection diagram

Operation

7.1 Setting the rotation speed

Details methods for setting the motor's desired rotation speed.

External potentiometer for speed setting

How to use an external potentiometer to control motor speed.

External DC voltage for speed setting

How to use external DC voltage for setting motor speed.

Internal potentiometer VR1 for speed setting

7.2 Setting the acceleration time and deceleration time

7.3 Operation and stop

Maintenance and inspection

8.1 Inspection

Inspection item

Troubleshooting

The motor does not rotate.

Steps to diagnose and resolve issues when the motor fails to operate.

A time for stopping is long.

The motor rotates in the opposite direction to the specified one.

The motor movement is not stable. Motor vibration is too large.

Alarms

10.1 Alarm reset

10.2 Alarm lists

Oriental motor BLH2D50-K Specifications

General

Brand	Oriental motor
Model	BLH2D50-K
Category	Engine
Language	English