What to do if my Oshkosh Corporation Boom Lifts shows high engine temp?
If your Oshkosh Corporation Boom Lifts engine temperature is high, check for any obstructions that might be blocking the cooling airflow to the engine. Also, make sure the ambient temperature is within the engine's design limits. Finally, verify that the engine temperature sensor is working correctly.
What to do if Oshkosh Corporation Boom Lifts unit is off or disabled and the engine will not crank?
If your Oshkosh Corporation Boom Lifts unit is off or disabled and the engine won't crank, check the position of the selector switch and ensure the inhibit run is released. Check the warning LED and address any faults before restarting the RBS. Verify the start battery voltage, check the control fuse, and inspect for loose wiring or connections.
What to do if my Oshkosh Corporation Boom Lifts is overcranking?
If your Oshkosh Corporation Boom Lifts is overcranking, start by checking the fuel level and connections. Then, verify the operation of the fuel solenoid and fuel pump. Also, check the start battery voltage. If you see white smoke from the engine exhaust, it means fuel is entering the engine but it's not firing. If the ambient temperature is low, make sure the heater or glow plug is working.
Why does my Oshkosh Corporation Boom Lifts have low oil pressure?
If your Oshkosh Corporation Boom Lifts has low oil pressure, first check the oil level and the oil supply lines. Verify the correct operation of oil pressure switch with a test gauge.
What causes underspeed in Oshkosh Corporation Boom Lifts?
If your Oshkosh Corporation Boom Lifts is experiencing underspeed, ensure the engine has an adequate supply of fuel and combustion air. Check the air cleaner. Also, verify the setting of the governor lever and readjust it if needed.
What causes overspeed in Oshkosh Corporation JLG E400AJP?
If your Oshkosh Corporation Boom Lifts is experiencing overspeed, verify the setting of the governor lever and readjust it if required.
How to troubleshoot engine starting system fault in Oshkosh Corporation Boom Lifts?
To troubleshoot an engine starting system fault in your Oshkosh Corporation Boom Lifts, check the engine start battery charging system for current output and inspect for a failed engine start battery.
What to do if my Oshkosh Corporation JLG E400AJP Boom Lifts shows overvoltage?
If your Oshkosh Corporation Boom Lifts is showing overvoltage, check the alternator output voltage.
What to do if my Oshkosh Corporation JLG E400AJP Boom Lifts has no speed signal?
If your Oshkosh Corporation Boom Lifts has no speed signal, check the wiring connections.
Outlines necessary precautions for proper and safe machine operation and maintenance.
Details operator training, pre-operation inspection, workplace, and machine checks.
Covers general operation rules and specific hazards like tipping and collision.
Provides instructions for safely towing, lifting, and hauling the machine.
Addresses other potential hazards and safety considerations during operation.
Details mandatory operator training, supervision, and responsibilities for safe operation.
Covers periodic machine inspections and maintenance schedules.
Explains the controls and indicators at the ground control station for machine operation.
Details the controls and indicators available at the operator's platform.
Describes the meaning of symbols and lights on the platform control indicator panel.
Outlines the machine's capabilities, load capacities, and operating limits.
Explains power, emergency stop, and motor activation procedures.
Covers safe driving practices, including speed, grades, and terrain.
Details how to steer the machine using the drive/steer controller.
Instructions for loading personnel, tools, and equipment onto the platform.
Describes how to swing and adjust the boom sections safely.
Information on generator operation modes and battery charging.
Details the inverter's role in converting DC power to AC for tools.
Explains how to adjust function speeds and properly shut down the machine.
Covers boom synchronization, lifting, and tie-down instructions.
Procedures for reporting incidents and operating the machine in emergencies.
Guidelines for safely towing the machine in case of malfunction or power failure.
Instructions for manually lowering booms and overriding swing in power failure situations.
Provides key operational data like capacity, reach, and dimensions.
Guidelines for daily operator maintenance tasks and lubrication points.
Instructions for quarterly battery maintenance and charging procedures.
Details tire inflation, damage criteria, replacement, and installation.
General| Fuel Type | Electric |
|---|---|
| Max Working Height | 46 ft (14.02 m) |
| Platform Height | 40 ft (12.19 m) |
| Platform Capacity | 230 kg |
| Platform Size | 0.76 m x 1.17 m |
| Weight | 14, 600 lb (6, 622.44 kg) |
| Drive Speed | 4 mph (6.4 km/h) |
| Machine Length | 20 ft |
| Stowed Height | 2.0 m |
| Lift Capacity | 500 lb (227 kg) |
| Tire Type | Solid |
| Horizontal Reach | 31 ft 3 in (9.53 m) |
To Next Page
