paasche TG-TALON - User Manual

INSTRUCTIONS & PARTS LIST TG-TALON-11/18/2008
Supersedes Instruction & Parts List TG-TALON-8/2008
INTRODUCTlON:
Prime Characteristics of the Paasche® TALON Airbrush include the ability to spray fluids requiring gravity feed doing fine detail and
shading work. The Double Action, Internal mix feature permits flexibility in regulation of color and air without work stoppage.
TG S
pecifications:
• Dual Action
• Head Size .38mm *
• .4 Ounce Gravity Cup
• Hair Line to 1-1/2 Inches
• Crown Cap
• Cutaway Handle with Pre-set Needle Stop
• New Style Trigger and Piston
* (other Head Sizes .25mm and .66mm)
W
orking Pressures:
• Operating pressures 20-55 PSI; Maximum pressure 85 PSI
• 20-30 PSI is best for detail spraying w/ properly thinned paint
• Use the higher pressures for thicker material where fine detail is not critical or thin the paint to allow lower pressures.
Equipment Set-up:
The Airbrush is held in the same manner as a pen, with the index finger comfortably over the finger button.
1. Attach air hose to air supply and to airbrush. If using a regulator set pressure between 20 -55 PSI.
Airbrush Operation:
1. Press down on Finger Button to release air and pull back on button to control quantity of color
.
2. To spray a fine line without heavy ends, start moving the airbrush without release of color. Then start the color at the beginning of line
and stop the color at the end, but continue the motion of the airbrush after the color has stopped.
3. Practice this movement until you can spray a fine line or a broad pattern without heavy build up at the beginning or end of your strokes.
4. S
peed of movement controls density of color and fading ef
fect
s at beginning and end of strokes.
5. For detail, hold the airbrush very close to the surface push down for air and pull back very slowly on the Finger Button to release a
small amount of p
aint.
6. For background work and broad ef
fects, hold the airbrush away from the work surface and pull back on Finger Button to release
required amount of color
.
7. For Stippling remove the aircap, push down on the trigger and pump the trigger forward and back. Adjust the air pressure between 15
and 50 PSI for desired stipple ef
fect.
8. For more instruction see the “22 Airbrush Lessons for Beginners” booklet enclosed with your airbrush.
Paasche Airbrush Company
4311 North Normandy Avenue
Chicago, IL 60634-1395
Printed in the U.S.A.
T
T
G
G
-
-
T
T
A
A
L
L
O
O
N
N
Gravity Feed - Internal Mix -
Double Action Airbrush
Phone: 773-867-9191 • Fax: 773-867-9198
W
ebsite: p
aascheairbrush.com
E-Mail: info@paascheairbrush.com
WARNING: Spray materials may be harmful if inhaled or allowed
to come into contact with the skin or eyes. Consult the product
label and Material Safety Data Sheet supplied for the spray
material. Follow all safety precautions. CAUTION: Well Ventilated
Area Required to remove fumes, dust or overspray. Secure airhose
to Airbrush with V-62 Wrench for safety and to prevent air leaks.
Maximum Air Pressure 75 P.S.I.
™

Summary

Introduction to Paasche TG Talon Airbrush

TG Specifications

Details on Dual Action, head size, cup capacity, spray pattern, and trigger features.

Working Pressures

Recommended and maximum air pressure ranges for operation and detail work.

Equipment Set-up

Instructions on connecting the air hose and setting air pressure.

Airbrush Operation Guide

Basic Operation

How to control air and color using the finger button.

Spraying Techniques

Guidance on spraying fine lines, broad patterns, and detail work.

Stippling

Instructions for performing stippling effects.

Airbrush Maintenance and Procedures

Removing and Replacing Needle and Handle

Step-by-step guide for needle and handle assembly.

Replacing Finger Lever Assembly

Procedure for inserting the finger lever assembly.

Replacing the Tip

Instructions for removing and installing the airbrush tip.

Adjusting Packing Washer

Guidance on tightening or replacing the packing washer.

Cleaning the Airbrush

Methods for cleaning the airbrush components.

Personal Settings

Adjusting spring tension for trigger comfort.

Troubleshooting Common Issues

Bubbling in Cup

Solutions for airbrush cup bubbling.

Skipping or Spitting

Troubleshooting steps for skipping or spitting spray.

Airbrush Not Spraying

Diagnosing and fixing issues when the airbrush is not spraying.

Uneven Spray Pattern

Addressing issues with double lines or uneven spray.

Jammed Trigger or Poor Motion

Resolving problems with a jammed or stiff trigger.

Accessories and Compressors

Airbrush Accessories

Listing of accessories like hangers and wrenches.

Air Hoses

Details on braided and red-plastic air hoses with couplings.

Airbrush Lube

Information on Paasche Airbrush Lube.

Moisture Trap Installation

Instructions for installing the MT Moisture Trap.

Recommended Air Compressors

Overview of various Paasche air compressor models.

paasche TG-TALON Specifications

General

Brand	paasche
Model	TG-TALON
Category	Airbrushes
Language	English