Palax COMBI M - Page 2

To Next Page

To Previous Page

Ohjekirja Palax combi M 2004.1 En

Main Page

Table of Contents3
Foreword7
Eu Declaration of Conformity7
Intended Use of the Machine8
Maximum Size of the Wood8
Markings Affixed to the Machine8
Nameplates8
Nameplate on the Machine8
Nameplates on the Electric Drive8
Safety Instructions9
Noise Emission and Vibration9
Responsibilities of the Operator9
Operating Conditions10
Machine Configurations10
Terms of Warranty10
The Warranty Covers10
The Warranty Does Not Cover11
Operating Instructions for the Combustion Engine11
Taking Delivery and Pre-Assembly of the Machine11
The Transport Set-Up and Unpacking11
Acceptance Inspection11
Main Parts of the Machine12
Ssembly of the Table Extension Igure 212
Ssembly of the Conveyor Support Igure 212
Protective Cover of Cross - Cut Saw - Blade , Figure 313
Protective Net of Cross - Cut Saw - Blade , Figure 313
Protective Cover of Splitting Trough , Figure 413
Assembly of the Log - Stop , Figure 513
Setting the Log Stop13
Topping up Hydraulic Oil13
Figure 313
Installing the V- Belt , Figure 614
Nstalling the Conveyor Winch Igure 914
Figure 1115
Installing the Winch Wire15
Bringing the Conveyor into the Transport Position15
Bringing the Conveyor into the Work Position15
Fixing the Lifting Handle , Figure 1015
Ocking the Debris Tray Igure 1015
Lifting and Transferring the Machine15
Operation of the Firewood Processor Powered by Different Power Sources16
Powered by a Tractor16
Emergency Stop Switch of the Tractor Powered Machine , Figure 1216
Operation of the Clutch, Figure 1216
Adjusting the Clutch, Figure 1316
Required Measures in an Emergency Situation17
Electric Drive, Start and Emergency Stop17
Starting17
Emergency Stop of a Machine Powered by Electric Motor, Figure 1417
Starting the Electric Motor at Sub-Zero Temperature, Figure 1217
Selecting the Power Source, Electricity or Tractor, Figure 15 and 1618
Honda Petrol Engine, Start, Stop and Emergency Stop18
Starting the Engine18
Stopping18
Emergency Stop18
Lombardini Diesel Engine, Start, Stop and Emergency Stop18
Use of the Firewood Processor, Cross-Cut Operation19
Preparations before the Use of the Machine, All Models19
Operating the Cross-Cut Saw, before the Operation19
During the Operation19
Placing the Wood on the Deck19
Right, the Log Is Supported by the Rollers, Figure 1820
Cross-Cut Operation20
Disturbances During Cross - Cut Operation and Their Remedy20
Crooked Trees20
Big Trees20
Cutting the Small Trees20
Use of the Firewood Processor, Splitting Operation20
Splitting Cylinder20
Manually - Operated High - Speed Valve , Figure 2020
Automatic High-Speed Valve21
Splitting Wedges21
Short, Straight Wedge, Optional21
In 2/4 Ways, Standard21
In 2/6 Ways, Option21
Manual Adjustment of the Splitting Blade21
Hydraulic Height Adjustment of the Splitting Blade, Optional21
Adjusting the Speed of the Splitting Blade Adjustment Cylinder22
Adjustment22
Disturbances During the Splitting Operation and Their Remedy22
Stuck Wood22
Re-Splitting the Logs Safely22
How the Safety Features Affect the Operation of the Machine22
Foot Pedal, Figure 2422
Protective Cover of Splitting Trough, Figure 2523
Operation of the Splitting Device23
Sensor23
Parts of the Splitting Device23
Operational Principle of Launching23
Hand - Start of the Splitting Motion , Figure 2823
Controls of the Hydraulic Valve24
Tightener, Part 124
Locking Lever, Part 224
Launching Rod, Part 324
Control Lever, Part 424
Hydraulic Valve, Part 524
Launching Spring, Part 624
Launching Lever, Part 724
Adjustment Mark, 824
Maintenance of the Machine24
Pre-Stressing the Saw-Blade, Hard-Metal Blade25
Guide of Cross - Cut Saw - Blade , Figure 3125
Adjustment of the Saw-Blade Guide25
Belts of the Angular Gear Igure 3225
Tightening the Belts25
Replacement of the V-Belts, Angle Gear, Figure 3326
Changing the Oil in the Angular Gear26
Lubricating the Machine , Fig 3426
Adjustment of the Conveyor Belt26
Tightening the Conveyor Belt, Figure 3526
Sideways Adjustment of the Belt, Upper End27
Sideways Adjustment of the Belt, Lower End, Figure 3627
Cleaning the Conveyor27
Washing the Machine27
Storing the Machine27
Maintenance Schedule28

Palax COMBI M - Page 2

Table of Contents

Related product manuals