Palax COMBI M - Table of Contents

Ohjekirja Palax combi M 2004.1 En
3
1 FOREWORD........................................................................................................................................................... 7
1.1 EU D
ECLARATION OF CONFORMITY ..................................................................................................................... 7
1.2 INTENDED USE OF THE MACHINE ........................................................................................................................... 8
Maximum size of the wood:....................................................................................................................................... 8
1.3 M
ARKINGS AFFIXED TO THE MACHINE .................................................................................................................. 8
1.4 NAMEPLATES ........................................................................................................................................................ 8
Nameplate on the machine ........................................................................................................................................ 8
Nameplates on the electric drive............................................................................................................................... 8
1.5 S
AFETY INSTRUCTIONS.......................................................................................................................................... 9
1.6 NOISE EMISSION AND VIBRATION .......................................................................................................................... 9
1.7 R
ESPONSIBILITIES OF THE OPERATOR .................................................................................................................... 9
1.8 OPERATING CONDITIONS ..................................................................................................................................... 10
1.9 M
ACHINE CONFIGURATIONS................................................................................................................................10
1.10 TERMS OF WARRANTY .................................................................................................................................... 10
The warranty covers................................................................................................................................................ 10
The warranty does not cover................................................................................................................................... 11
1.11 O
PERATING INSTRUCTIONS FOR THE COMBUSTION ENGINE ............................................................................ 11
2 TAKING DELIVERY AND PRE-ASSEMBLY OF THE MACHINE ............................................................ 11
2.1 T
HE TRANSPORT SET-UP AND UNPACKING........................................................................................................... 11
2.2 ACCEPTANCE INSPECTION ................................................................................................................................... 11
2.3 MAIN PARTS OF THE MACHINE ............................................................................................................................ 12
2.4 A
SSEMBLY OF THE TABLE EXTENSION, FIGURE 2 ................................................................................................ 12
2.5 ASSEMBLY OF THE CONVEYOR SUPPORT, FIGURE 2............................................................................................. 12
2.6 PROTECTIVE COVER OF CROSS-CUT SAW-BLADE, FIGURE 3................................................................................. 13
2.7 P
ROTECTIVE NET OF CROSS-CUT SAW-BLADE, FIGURE 3 ..................................................................................... 13
2.8 PROTECTIVE COVER OF SPLITTING TROUGH, FIGURE 4 ........................................................................................ 13
2.9 ASSEMBLY OF THE LOG-STOP, FIGURE 5 ............................................................................................................. 13
2.10 S
ETTING THE LOG-STOP .................................................................................................................................. 13
2.11 TOPPING UP HYDRAULIC OIL........................................................................................................................... 13
2.12 ASSEMBLY OF THE CONVEYOR, FIGURE 6....................................................................................................... 14
2.13 I
NSTALLING THE V-BELT, FIGURE 6 ............................................................................................................... 14
2.14 INSTALLING THE ATTACHMENT PLATE AND THE SUPPORT WIRES, FIGURE 8................................................... 14
2.15 I
NSTALLING THE CONVEYOR WINCH, FIGURE 9 .............................................................................................. 14
2.16 INSTALLING THE WINCH WIRE ........................................................................................................................ 15
2.17 BRINGING THE CONVEYOR INTO THE TRANSPORT POSITION............................................................................ 15
2.18 B
RINGING THE CONVEYOR INTO THE WORK POSITION .................................................................................... 15
2.19 F
IXING THE LIFTING HANDLE, FIGURE 10 ....................................................................................................... 15
2.20 L
OCKING THE DEBRIS TRAY, FIGURE 10 ......................................................................................................... 15
2.21 L
IFTING AND TRANSFERRING THE MACHINE, FIGURE 11 ................................................................................ 15
3 OPERATION OF THE FIREWOOD PROCESSOR POWERED BY DIFFERENT POWER SOURCES 16
3.1 P
OWERED BY A TRACTOR .................................................................................................................................... 16
3.2 E
MERGENCY STOP SWITCH OF THE TRACTOR POWERED MACHINE, FIGURE 12 .................................................... 16
Operation of the clutch, Figure 12.......................................................................................................................... 16
Adjusting the clutch, Figure 13............................................................................................................................... 16
Required measures in an emergency situation........................................................................................................ 17
3.3 E
LECTRIC DRIVE, START AND EMERGENCY STOP ................................................................................................. 17
Starting.................................................................................................................................................................... 17
Emergency stop of a machine powered by electric motor, Figure 14 ..................................................................... 17
Starting the electric motor at sub-zero temperature, Figure 12.............................................................................. 17
Selecting the power source, electricity or tractor, Figure 15 and 16...................................................................... 18
3.4 H
ONDA PETROL ENGINE, START, STOP AND EMERGENCY STOP............................................................................ 18
Starting the engine .................................................................................................................................................. 18
Stopping .................................................................................................................................................................. 18
Emergency stop....................................................................................................................................................... 18
3.5 L
OMBARDINI DIESEL ENGINE, START, STOP AND EMERGENCY STOP.................................................................... 18
Stopping .................................................................................................................................................................. 18
Emergency stop....................................................................................................................................................... 18
4 USE OF THE FIREWOOD PROCESSOR, CROSS-CUT OPERATION ...................................................... 19
4.1 P
REPARATIONS BEFORE THE USE OF THE MACHINE, ALL MODELS........................................................................ 19
4.2 OPERATING THE CROSS-CUT SAW, BEFORE THE OPERATION ................................................................................ 19