83
Menu Displays
Setup menu list
[SCENE FILE] screen
Item
Display
mode
Description of settings
[LOAD/SAVE/
INIT]
<CAMERA>
[LOAD]: Loads the scene le settings saved in this camera.
[SAVE]: Saves the updated scene le settings.
[INIT]: Returns the scene le settings selected using the <SCENE FILE>
dial, to the factory settings.
[NO]: Returns to the previous screen.
[VFR MODE] <CAMERA>
(AVCHD
mode only)
[ON]: Enables the VFR (Variable Frame Rate) mode.
[OFF]: Disables the VFR mode.
Operates only when [REC FORMAT] is [PH 1080/24P], [PH 1080/30P], or [PH
1080/25P].
When [SDI 24PsF] = [ON], VFR operation is disabled.
When [VFR MODE] = [ON], you cannot record audio.
When VFR mode is set to [ON], INTERVAL REC, relay recording, and SIMUL
REC settings will all be cancelled. This mode cannot be used with INTERVAL
REC, relay recording, SIMUL REC, and pre-rec functions.
[FRAME RATE] <CAMERA>
(AVCHD
mode only)
Sets [FRAME RATE].
Operates when [VFR MODE] is [ON].
You can set using <SHTR/F.RATE> on the left side of the camera body.
When [SYSTEM FREQ] = [59.94Hz]
When [REC FORMAT] = [PH 1080/24P] [PH 1080/30P]:
[2]/[6]/[9]/[12]/[15]/[18]/[20]/[21]/[22]/[24]/[25]/[26]/[27]/[28]/[30]/[32]/[34]/[36]/
[40]/[44]/[48]/[54]/[60]
When [SYSTEM FREQ] = [50Hz]
When [REC FORMAT] = [PH 1080/25P]
[2]/[6]/[9]/[12]/[15]/[18]/[20]/[21]/[22]/[23]/[24]/[25]/[26]/[27]/[28]/[30]/[32]/[34]/
[37]/[42]/[45]/[48]/[50]
[SYNC SCAN
TYPE]
<CAMERA>
Selects the synchro scan display setting.
[deg.]: Sets to angle display.
[sec]: Sets to speed display.
[SYNCHRO
SCAN]
<CAMERA>
Adjusts the synchro scan shutter speed used for shooting images on a TV
screen, etc.
Holding the OPERATION lever tilted upward or downward will cause the values
to change at a faster rate.
When [SYSTEM FREQ] = [59.94Hz]
•
When [SYNC SCAN TYPE] = [sec]
60i/60 P mode: [1/60.0] - [1/249.8] secs
30 P mode: [1/30.0] - [1/48.0] - [1/249.8] secs
24 P mode: [1/24.0] - [1/48.0] - [1/249.8] secs
•
When [SYNC SCAN TYPE] = [deg.]
[3.0 d] - [180.0 d] - [360.0 d] (0.5 d increments, angle display)
When [SYSTEM FREQ] = [50Hz]
•
When [SYNC SCAN TYPE] = [sec]
50i/50 P mode: [1/50.0] - [1/250.0] secs
25 P mode: [1/25.0] - [1/50.0] - [1/250.0] secs
•
When [SYNC SCAN TYPE] = [deg.]
[3.0 d] - [180.0 d] - [360.0 d] (0.5 d increments, angle display)
is the factory default mode for the <SCENE FILE> dial <F1>.
Menu
To Next Page
Loading...
