Panasonic CF-28 Series - Page 26

Troubleshooting
Reinstalling Software
When the message “Insert media 2...” is displayed, insert
Product Recovery CD-ROM 2 after removing Product Re¬
covery CD-ROM 1, and then immediately press [OK].
Xnote> -—-.
If [OK] is not immediately pressed:
The message “The media does not contain the cor¬
rect file” may appear. In such cases, the message
“Insert media 2...” is displayed again when [OK] is
pressed. Confirm that Product Recovery CD-ROM
2 has been inserted by opening the tray of the CD-
ROM/DVD-ROM drive, and then close the tray and
immediately press [OK],
V_^- ✓
9 After the reinstallation procedure completes, the follow¬
ing message will appear on the display.
iWI ndowsl98iltWi ndo^NTA
All data on the whole HDD has been restored to the factory default.
After removing floppy disk, restart the computer and set up Windows again.
Remove the disk, then restart the computer by pressing
r^Fn + r ^+fDin.
4Wlndows)2000l
Windows2000 install wizard will start after reboot.
Restore process will execute more after Windows2000 install wizard.
After removing the Product Recovery CD, power off your computer.
Replace the CD-ROM pack with the FDD.
Turn your computer on to continue re-installation.
Remove the Product Recovery CD-ROM and then power
the computer off. Replace the CD-ROM/DVD-ROM drive
with the floppy disk drive and turn the computer on.
iWindowsiNTA
Restart the computer automatically.
If the message "Preinstallation completed successfully.
Press any key to shut down/reboot." is displayed, press
any key.
11 When the mes s a ge [Press <F2> to enter SETUP] is dis¬
played, press C F2 ) and then run the Setup Utility.
If the password has been set, enter the Supervisor Pass¬
word. _
12 Press dD
At the confirmation message, select [Yes] and press
C Enter ) . (The Setup Utility settings will return to their
default values. Even the security settings with the excep¬
tion of the password(s) will return to their default values.)
Chang e the s ettings where necessary.
13 Press ( FIO) .
At the confirmation message, select [Yes] and press
C Enter) .
14 Perform the setup procedure for Windows by following
the instructions on the screen.
15 _ _
<When the BACKUP DISK has been created Q= page 12>
Set the BACKUP DISK and select [OK].
(If the BACKUP DISK has not been created, select [Can¬
cel].)
# Setup Windows
(l^ The Software License Agreement will be displayed.
After reading the agreement, select [I Agree].
^NOTE) -^^
• If [I Disagree] is selected, the Windows setup
wilt be aborted.
• Moving the cursor ([^) or clicking buttons can
be performed with the touch pad.
V___/
Select [Next],
Input your name and organization, then select [Next].
(It is possible to omit the organization item.)
(T) Input the Product ID written down in the column
“Customer’s record” (C^page 2) then select [Next].
To move the cursor to a particular item, press
nib^ or click the desired box.
(J) Input your computer name and select [Next],
Input an Administrator password and select [Next].
^- ■
Remember this password! If the password is for¬
gotten, Windows NT cannot be operated.
(t) Select [Next],
@ Select [Do not connect this computer to a network at
this time], then select [Next],
(Settings can be made for a network even after Win¬
dows starts up. In this case, be sure to read [When
Adding New Software or Hardware Components] in
the Reference Manual [Technical Information].)
• When establishing settings for a network;
The settings will vary for different network envi¬
ronments depending on the network system being
used. For more details, ask your system adminis¬
trator or the person in charge of the network. Fol¬
low the on-screen instructions.
Xnote) -,
It takes several minutes for the necessary files to
be copied. If the computer enters the ECO mode,
the power to the LCD is automatically turned off.
In this case, press a key unrelated to the direct
triggering of a selection, like C Ctrl ) .
26