To Next PageTo Next PageWhy does the external display not work normally with my Panasonic CF-C2 Laptop?
If the external display does not support the power saving function, it may not work normally when the computer enters the power saving mode. Turn off the external display.
What should I do if my Panasonic CF-C2 won't turn on or resume from sleep?
To resolve this issue, the computer should be in an environment of 5 °C or higher temperature for about an hour, then turn on the power again.
Why is my Panasonic CF-C2 Laptop Windows startup and operation slow?
To address slow Windows performance on your Panasonic Laptop: * Press F9 in the Setup Utility to return the Setup Utility settings (excluding the passwords) to the default values. Start the Setup Utility and make the settings again. (Note that the processing speed depends on the application software, so this procedure may not make Windows faster.) * If you installed a resident software after purchase, turn off the residence.
How to brighten a dark screen on a Panasonic CF-C2 Laptop?
To fix a dark screen on your Panasonic Laptop: * The screen is darker when the AC adaptor is not connected. Press Fn + F2 and adjust the brightness. As you increase the brightness, battery consumption increases. * You can separately set the brightness for when the AC adaptor is connected and when not connected. * Press Fn + F8 to turn off the concealed mode.
How to resolve network connection issues on a Panasonic Laptop?
Try the following: * Slide the wireless switch to turn on the wireless devices. * Set the device ([Wireless LAN] / [Bluetooth] / [Wireless WAN] of [Wireless Configuration]) to [Enabled] in the [Advanced] menu of the Setup Utility (Wireless Configuration). * Click [Charm] - [Change PC Settings] - [Wireless]. Set [Airplane mode] to [Off], and then; set [Wi-Fi] in “Wireless device” to [On] (for wireless LAN). set [Mobile broadband] in “Wireless device” to [On] (for wireless WAN). set [Bluetooth] in “Wireless device” to [On] (for Bluetooth).
What to do if 'Remove disks or other media' appears on my Panasonic Laptop?
If you see this message, it might be due to: * A floppy disk is in the drive and it does not contain system startup information. Remove the floppy disk and press any key. * If a device is connected to the USB port, disconnect the device, or set [USB Port] or [Legacy USB Support] to [Disable] in the [Advanced] menu of the Setup Utility. * If a device is connected to the ExpressCard slot, disconnect the device, or set [ExpressCard Slot] to [Disable] in the [Advanced] menu of the Setup Utility. If the problem persists after removing the disk, it may be a hard disk failure. Contact Panasonic Technical Support.
How to troubleshoot no display on my Panasonic CF-C2 Laptop?
To resolve this: * Press Fn + F3 or key + P to switch the display. Wait until the display has been switched completely before pressing Fn + F3 or key + P again. * When using an external display: * Check the cable connection. * Turn on the display. * Check the settings of external display. * The display is turned off by the power-saving function. To resume, do not press the direct selection keys, but press any other key like Ctrl. * The computer entered sleep or hibernation by the power-saving function. To resume, press the power switch.
What to do if my Panasonic CF-C2 Windows does not shut down?
Here are some steps you can take: * Remove the USB device and the ExpressCard. * Wait one or two minutes. It is not a malfunction.
How to fix a Panasonic CF-C2 Laptop that cannot start, and the power indicator is off?
To potentially resolve the issue, try the following: * Connect the AC adaptor. * Insert a fully charged battery. * Remove the battery pack and the AC adaptor, then connect them again. * If a device is connected to the USB port, disconnect the device, or set [USB Port] or [Legacy USB Support] to [Disable] in the [Advanced] menu of the Setup Utility. * If a device is connected to the ExpressCard slot, disconnect the device, or set [ExpressCard Slot] to [Disable] in the [Advanced] menu of the Setup Utility. * Press Fn + F8 to turn off the concealed mode. * Check the [UEFI Boot] setting of the Setup Utility. [UEFI Boot] should be set to [Enabled] / [Disabled].
General| Resolution | 1366 x 768 |
|---|---|
| RAM | 4GB |
| Storage | 500GB HDD |
| Display | 12.5-inch |
| Graphics | Intel HD Graphics |
| Operating System | Windows 7 Professional |
| Battery Life | Up to 11 hours |
| Touchscreen | Yes |
| Convertible | Yes |
| Battery | 6-cell |
| Wireless | Wi-Fi 802.11a/b/g/n |
| Ports | VGA, Ethernet, SD card |
Essential safety guidelines for product usage, handling, and potential hazards.
Compliance statements, FCC/IC regulations, and safety advisories for various wireless and regional standards.
Welcome message, overview of manual conventions, and product trademarks.
Guidance on accessing on-screen manuals, reference materials, and battery optimization tips.
Identification of computer parts, display modes, pen attachment, and hand strap usage.
Step-by-step guide for initial setup, connecting power, turning the device on/off, and basic configuration.
Guidelines for operating environment, handling precautions, cleaning, and computer disposal procedures.
Procedures for installing software, performing hard disk recovery, and managing operating system versions.
Solutions for common startup issues, password problems, display errors, and connectivity problems.
Legal terms and conditions for software usage and licensing.
Detailed technical specifications for hardware components, wireless capabilities, and software configurations.
Warranty terms and conditions for hardware, software, and accessories in different regions (USA, Canada).
