NAME OF EACH PART
■ Remote Control
● Remote Control Signal.
• Make sure it is not obstructed.
• Maximum distance : 10 m.
• Signal received sound.
One short beep or one long beep.
● Notes for Remote Control.
• Do not throw or drop.
• Do not get it wet.
• Certain type of fluorescent lamps may affect
signal reception. Consult your dealer.
● How to Insert the Batteries
1
Slide down the remote control cover completely
2
Insert the batteries
– Be sure the direction is correct
– 12.00 at display - flashing
• Set the current time (CLOCK) immediately to
prevent battery exhaustion.
● About the batteries
• Can be used for approximately one year.
● Observe the following when replacing the
batteries
• Replace with new batteries of the same type.
• Do not use rechargeable batteries (Ni-Cd).
• Remove the batteries if the unit is not going to be
used for a long period.
1 Signal Transmitter
2 Operation Display
3 Powerful Mode Operation Button
4 Room Temperature Setting Button
(self-illuminating button)
5 Operation Mode Selection Button
6 Vertical Airflow Direction Button
7 ON-Timer Button
8 OFF-Timer Button
9 Reset Point
(Press with fine-tipped object to clear the memory)
0 Check Point
To be used by the service technician only.
! OFF/ON Button
(self-illuminating button)
@ Sleep Mode Operation Button
# Fan Speed Selection Button
$ Horizontal Airflow Direction Button
% Timer Set Button
^ Timer Cancellation Button
& Time-Setting Button
* Clock Button
( Remote Control Cover
AUTO
OF
AUTOHEAT
DRYFA NCOOL
FAN
AUTO
AUTO
R
ES
ET
C
LO
C
K
AIR SW
ING
OFF
C
A
N
C
E
L
1
2
3
TIMER
P
O
W
E
R
F
U
L
AUTO
MANUAL
ECO
NO
M
Y
SLE
ON
S
E
T
FAN SPEED
MODE
C
HE
C
K
ECONOMY
TEMP
AUTUTO
ON
OFF
AUTUTOHEAHEAT DRDRYFANANCOOLCOOL
FANAN
AUTUTO
AUTUTO
CLOCK
MODE
SLEEP
FAN SPEED
AIR SWING
OFF
CANCEL
ON
SET
1
2
3
TIMER
OFF/ON
POWERFUL
#
!
$
%
^
$
*
&
3
5
7
6
8
9
4
(
CHECK RESET
2
1
0
PREPARATION BEFORE OPERATION
■ Indoor Unit
1
Connect the power supply cord to an independent
power supply
2
Open the front panel
3
Remove the air filters
4
Fit the air purifying filters in place
5
Insert the air filters
6
Close the front panel
■ Remote Control
– To set the current time
1
Press 1.
2
Then press 2 to increase or decrease the time.
3
Press 1 again.
Set time at display will light up.
AUTO
AUTO HEAT DRY FANCOOL
FAN
AUTO
CLOCK
FAN SPEED
AIR SWING
OFF
CANCEL
ON
SET
1
2
3
TIMER
1
2
RESETCHECK
6
2
1
4
5
3
■ Setting Temperature
• Press 3 to increase or decrease the temperature.
• The temperature can be set between 16°C ~ 30°C.
(Not adjustable during Fan Operation.)
• Recommended temperature:
HEAT : 20°C ~ 24°C
COOL : 26°C ~ 28°C
DRY : Approx. room temperature
■ Automatic Operation
• At the start of the Automatic operation, Heating,
Cooling or Soft Dry is automatically selected according
to the outdoor temperature, indoor temperature and
setting temperature.
• The operation mode changes every half hour, when
necessary.
HOW TO OPERATE
■ To start the operation
• Press 1.
•
POWER indicator (green) on the indoor unit will light up.
(LED blinks when the room temperature is low at the
start of heating or operation mode is selected during
Automatic Operation.)
The power monitor lamps light up to show the
compressor operating condition.
• To stop, press once more.
■ Setting Mode
• Press 2 to select:-
HEAT – Heating Operation
COOL – Cooling Operation
DRY – Soft Dry Operation
FAN – Fan Operation
AUTO – Automatic Operation
EC
O
N
O
M
Y
O
F
F
ON
HEAHEAT DRDRYFANANCOOL
COOL
C
H
E
C
K
TEMP
AUTUTO
AUTUTO
FANAN
AUTO
R
E
S
E
T
C
L
O
C
K
AIR SWING
OFF
CANCEL
1
2
3
T
IM
E
R
O
FF/O
N
P
O
W
E
R
F
U
L
SLEEP
ON
SET
FAN SPEED
MODE
AUTO
2
3
5
1
6
4
13°C 19°C 21°C 23°C 25°C
36°C
32°C
31°C
18°C
16°C
(Ex) Setting Temperature at 25°C
Outdoor Temperature
Room Temperature
C
O
O
L
I
N
G
S
O
F
T
D
R
Y
H
E
A
T
I
N
G
37
CS-E9BKP CU-E9BKP5 / CS-E12BKP CU-E12BKP5
To Next Page
Loading...
Need help?
General
