63
VQT2J28
Setting menus
[RAM]
Preparation
≥Press [DRIVE SELECT] to select the DVD drive.
1 Press [3, 4] to select “Disc
Protection” and press [OK].
2 Press [2, 1] to select “Yes” and
press [OK].
The lock symbol appears closed when the disc is write-
protected.
To return to the previous screen
Press [RETURN ].
To exit the screen
Press [EXIT].
[SD]
Switch the write-protect switch to the “LOCK” position.
[HDD] [RAM]
Preparation
≥Press [DRIVE SELECT] to select the HDD or DVD drive.
After performing steps 1–3 (> 62, Common procedures)
1 Press [3, 4] to select “Delete all
titles” and press [OK].
2 Press [2, 1] to select “Yes” and
press [OK].
3 Press [2, 1] to select “Start” and
press [OK].
A message appears when finished.
4 Press [OK].
To return to the previous screen
Press [RETURN ].
To exit the screen
Press [EXIT].
≥Once deleted, the recorded contents are lost and cannot be
restored. Make certain before proceeding.
≥Deleting all video titles will result in all Playlists (Video) also being
deleted.
≥Still picture data (JPEG), Playlists (Picture), music data or
computer data cannot be deleted.
≥Delete does not work if one or more titles are protected.
[RAM] [-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] [+RW]
You can provide a name for each disc.
Preparation
≥Press [DRIVE SELECT] to select the DVD drive.
After performing steps 1–3 (> 62, Common procedures)
1 Press [3, 4] to select “Disc Name”
and press [OK].
(> 43, Entering text)
≥The disc name is displayed in the DVD Management window.
≥[-R] [-R]DL] [-RW‹V›] [+R] [+R]DL] With a finalised disc, the name is
displayed on the Top Menu.
≥[+RW] The disc name is displayed only if you play the disc on other
equipment after creating top menu.
≥[-R] Once a name is provided to a disc, it is not possible to record
still images to that disc.
To return to the previous screen
Press [RETURN ].
To exit the screen
Press [EXIT].
[HDD] [RAM] [-RW‹V›] [+RW] [-RW‹VR›]
[+R] [+R]DL] (New disc only)
[SD]
Preparation
≥Press [DRIVE SELECT] to select the HDD, DVD or SD drive.
≥[SD] Release protection (> left, Setting the protection).
After performing steps 1–3 (> 62, Common procedures)
1 Press [3, 4] to select “Format HDD”,
“Format Disc” or “Format Card” and
press [OK].
2 Press [2, 1] to select “Yes” and
press [OK].
3 Press [2, 1] to select “Start” and
press [OK].
A message appears when formatting is finished.
≥Formatting normally takes a few minutes; however, it may
take up to a maximum of 70 minutes ([RAM]).
≥Do not disconnect the AC mains lead while formatting.
This can render the disc or the card unusable.
4 Press [OK].
≥When a disc or card has been formatted using this unit, it may not
be possible to use it on any other equipment.
≥[-R] [-R]DL] [CD] Formatting cannot be performed.
≥You can format DVD-RW only as DVD-Video format on this unit.
≥Sample pictures are restored when formatting HDD even if they
have been deleted.
To return to the previous screen
Press [RETURN ].
To exit the screen
Press [EXIT].
Setting the protection
After performing steps 1–3 (> 62, Common procedures)
Card-protection
Deleting all titles and
Playlists (Video)—Delete all titles
≥[RAM] Release protection (> above).
DVD
Management
DVD-RAM
Titles 11
Used
Remain
0 : 22
5:38 (EP)
On
Disc Name
Delete all titles
Format Disc
Disc Protection
OK
RETURN
SELECT
LOCK
Note
Providing a name for a disc
≥[RAM] Release protection (> left, Setting the protection).
Deleting all the contents—Format
Formatting deletes all contents (including computer data),
and they cannot be restored. Check carefully before
proceeding. The contents are deleted when you format a disc or
card even if you have set protection.
My favorite 01/02
01
Chapter 1
03
02
04
Chapter 2
DVD
Management
DVD-RAM
Titles 11
Used
Remain
0 : 22
5:38
Documentary
Note
Note
Note
DMREX83EG&EC-VQT2J28_eng.book 63 ページ ２０１０年１月１８日 月曜日 午後２時２９分
To Next Page
Loading...
Need help?
General
