RQT7258
15
∫ “HDMI” tab
∫ “Display” tab
∫ “Others” tab
§1
Language options:
French, German, Italian, Spanish, Portuguese, Swedish and Dutch
§2
The original language designed on the disc is selected.
§3
Input a code number referring to the table on page 16.
§4
If the language selected for “Audio” is not available, subtitle appear in
that language (If available on the disc).
§5
[The\United\Kingdom\and\Continental\Europe]
If you select “Multi-channel” (➜ page 14, “Speaker Settings” in “Audio” tab), the following setting (a) is required. (Select settings b c to suit your
preference if desirable.)
1. Press [3 4 2 1] to select an item and press [ENTER].
2. Press [3 4] to change the content and press [ENTER].
Icon examples:
Surround speaker (LS)
≥ Large: Select when the speaker supports low-frequency (under 100 Hz)
reproduction.
≥ Small: Select when the speaker does not support low-frequency
reproduction.
If the subwoofer is set to “No”, the front speakers will automatically be set
to “Large”. (In this case, we recommend connecting a speaker that can
reproduce bass below 100 Hz.)
(Effective when playing multi-channel audio)
If either distance d or f is less than e, find the difference in the relevant
table and change to the recommended setting.
1. Press [3 4 2 1] to select an item and press [ENTER].
2. Press [3 4] to change the content and press [ENTER].
This does not work when connected with HDMI terminals and “HDMI
Audio Output” (
➜
above,
“
HDMI
”
tab)
is set to “On”.
1. Select “Test” and press [ENTER].
A test signal is output.
Front (L)_—)Center_—)Front (R)
:;
Surround (LS)(—————=Surround (RS)
2. While listening to the test signal, press [3 4] to adjust the
volume of the center and surround speakers so they are the
same apparent volume as the front speakers (s6 to r6 dB).
(The front speakers cannot be adjusted here.)
3. Press [ENTER].
The test signal stops.
≥No signal is output for the subwoofer. To adjust its volume, play
something, then return to this screen to adjust to suit your taste.
To finish the speaker setting
Press [3 4 2 1] to select “Exit” and press [ENTER].
HDMI RGB Range
Set
“
HDMI Colour Space
” to
“RGB” (
➜
page
12, Picture Menu) .
≥ Standard
≥ Enhanced: When the black and white images are not distinct.
HDMI Video Mode
≥ On: When video output is from HDMI AV OUT terminal.
≥ Off: When video output is from COMPONENT VIDEO OUT terminal [output is “525 (480)p” or “625
(576)p” from HDMI AV OUT terminal].
HDMI Audio Output
≥ On: When audio output is from HDMI AV OUT terminal.
≥ Off: When audio output is not from HDMI AV OUT terminal.
Menu Language ≥ English ≥ Français ≥ Deutsch ≥ Italiano ≥ Español ≥ Português ≥ Svenska≥ Nederlands
On-Screen Messages
≥ On ≥ Off
Background during Play
Select background during JPEG and
MPEG4 playback.
≥ Black ≥ Grey
FL Dimmer
Changes the brightness of the unit’s display.
≥ Bright ≥ Dim
≥ Auto:The display is dimmed during play, but brightens when you perform some operations.
Auto Power Off
≥ On:
The unit switches to standby mode after about 30 minutes in the stop mode, irrespective of the SLEEP setting.
≥ Off
QUICK SETUP
≥ Ye s ≥ No
Re-initialise Setting
This returns all values in the Setup menus to
the default settings.
≥
Yes: The password screen is shown if “Ratings” (
➜
page 14) is set. Please enter the same password.
After “INIT” on the display disappears, turn the unit off and on again.
≥ No
Changing the speaker setting to suit your speakers
Speaker presence and size (a)
m s
m s
d B
0
d Bd B
L
Exit
Test
LS
R
SW
C
RS
d B
0
0
0.0
0
0.0
b a c
a
a
c a
(LS) (RS)
a c b c a
Exit
Test
signal
Front (L) Center Front (R)
— Surround —
Subwoofer
LS
LS
NoLarge Small
Delay time (b)
d Center speaker
Difference Setting
Approx. 34 cm 1.0 ms
Approx. 68 cm 2.0 ms
Approx. 102 cm 3.0 ms
Approx. 136 cm 4.0 ms
Approx. 170 cm 5.0 ms
f Surround speakers
Difference Setting
Approx. 170 cm 5.0 ms
Approx. 340 cm
10.0 ms
Approx. 510 cm
15.0 ms
Channel balance (c)
LS
RS
L
R
SW
f
e
d
C
: Recommended placement
Changing the player settings
To Next Page
Loading...
