64
KX-FP207FX-S/FP218FX-S
580 TAM continuous tone detection (KX-
FP218)
1:ON 2:OFF 1, 2 1 ON : Stops TAM operation when Dial tone, etc. are
detected.
590 FAX auto redial time set X number of
times
00~99 05 Selects the number of redial times during FAX commu-
nication (not including the first dial).
591 FAX auto redial time disconnection
time set
X second 001~999 065 Sets the FAX redial interval during FAX communication.
592 CNG transmit select 1:OFF
2:ALL
3:AUTO
1~3 2 Lets you select the CNG output during FAX transmis-
sion. ALL: CNG is output at phase A. AUTO: CNG id
output only when automatic dialling is performed. OFF:
CNG id not output at phase A. Refer to Sometime
there is a transmit problem (P.90).
593 Time between CED and 300bps 1:75 msec
2:500 msec
3:1 sec
1~3 1 See Symptom/Countermeasure Table for long dis-
tance and international calls in The unit can copy, but
cannot either transmit/receive long distance or
international communications (P.93). Refer to
Receive Problem (P.91) .
594 Overseas DIS detection select 1:detects at
the 1st time
2:detects at
the 2st time
1, 2 1 See Symptom/Countermeasure Table for long dis-
tance and international calls in The unit can copy, but
cannot either transmit/receive long distance or
international communications (P.93). Refer to Some-
time there is a transmit problem (P.90).
595 Receive error limit value set 1:5 %
2:10 %
3:15 %
4:20%
1~4 2 Refer to Receive Problem (P.91).
596 Transmit level set X dbm
(10 = -10 dbm)
- 15~00 10 Selects the FAX transmission level. Refer to Sometime
there is a transmit problem (P.90) and Receive Prob-
lem (P.91).
598 Receiving sensitivity X dbm
(40 = -40 dbm)
-20~-48 42 Used when there is an error problem. Refer to The unit
can copy, but cannot either transmit/receive long
distance or international communications (P.93).
Power is OFF/ON after changing this set value.
599 ECM frame size 1:256 2:64 1, 2 1 ----------
710 Memory clear except History data Refer to Memory Clear Specification (P.66).
717 Transmit speed selection (KX-FP207) 1:9600BPS
2:7200BPS
3:4800BPS
4:2400BPS
1~4 1 Adjusts the speed to start training during FAX transmis-
sion. Refer to Sometime there is a transmit problem
(P.90) and The unit can copy, but the transmission
and reception image are incorrect (P.95).
717 Transmit speed selection (KX-FP218) 1:14400BPS
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
1~6 1 Adjusts the speed to start training during FAX transmis-
sion. Refer to Sometime there is a transmit problem
(P.90) and The unit can copy, but the transmission
and reception image are incorrect (P.95).
718 Receive speed selection (KX-FP207) 1:9600BPS
2:7200BPS
3:4800BPS
4:2400BPS
1~4 1 Adjusts the speed to start training during FAX recep-
tion. Refer to Receive Problem (P.91) and The unit
can copy, but the transmission and reception image
are incorrect (P.95).
718 Receive speed selection (KX-FP218) 1:14400BPS
2:12000BPS
3:9600BPS
4:7200BPS
5:4800BPS
6:2400BPS
1~6 1 Adjusts the speed to start training during FAX recep-
tion. Refer to Receive Problem (P.91) and The unit
can copy, but the transmission and reception image
are incorrect (P.95).
722 Redial tone detect 1:ON 2:OFF 1, 2 1 Sets the tone detection mode after redialling.
745 Power ON film feed 1:ON 2:OFF 1, 2 1 When the power is turned on, the film is wound to take
up any slack.
763 CNG detect time for friendly reception 1:10 sec
2:20 sec
3:30 sec
1~3 3 Selects the CNG detection tone of friendly reception.
773 DIS-DIC interval 1: 500msec
2: 200msec
1, 2 2 This is similar to #594. The time interval from receiving
DIS to sending DCS can be changed to wait for the
echo canceler to recover.
774 T4 timer X 100 msec 00~99 0 Use this function when delay occurs in the line and
communication (ex. Mobile comm) does not work well.
784 Voice prompt test (KX-FP218) See Test Mode (P.58).
815 Sensor & Vox check See Test Mode (P.58).
Code Function Set Value Effective
Range
Default Remarks
To Next Page
Loading...
