Panasonic KX-TG2511CX User Manual (English)

Other manuals for Panasonic KX-TG2511CX

Questions and Answers:

M
megan97Aug 21, 2025
Why does my Panasonic KX-TG2511CX Cordless Telephone have noise and cuts in and out?
- S
  Sherry LoweryAug 21, 2025
  If you hear noise or the sound cuts in and out while using your Panasonic Cordless Telephone, it might be due to electrical interference in the area. Try repositioning the base unit and using the handset away from these sources. Also, move closer to the base unit. If you have DSL/ADSL service, consider using a DSL/ADSL filter between the base unit and the telephone line jack. You can also try resetting the unit by unplugging the base unit’s AC adapter, turning off the handset, reconnecting the adapter, and turning the handset back on.
A
Amy RangelAug 22, 2025
Why does my Panasonic KX-TG2511CX beep and flash 7 times?
- E
  Elizabeth MeyerAug 23, 2025
  If your Panasonic Cordless Telephone handset beeps and/or flashes 7 times, it means the battery charge is low. You should fully charge the batteries.
S
Steven YangAug 25, 2025
How to fix Panasonic Cordless Telephone when I cannot hear a dial tone?
- B
  Brianna GonzalezAug 25, 2025
  If you cannot hear a dial tone on your Panasonic Cordless Telephone, ensure you are using the supplied telephone line cord, as older cords may have different wiring. Check that the base unit’s AC adapter and telephone line cord are properly connected. You can also test the telephone line by disconnecting the base unit and connecting the line to a known working telephone. If the working telephone operates correctly, the unit may need repair. If not, contact your service provider.
H
hsmithAug 26, 2025
What to do if my Panasonic Cordless Telephone unit does not work?
- S
  sanchezkatrinaAug 27, 2025
  If your Panasonic Cordless Telephone unit does not work, make sure the batteries are installed correctly and fully charged. Check all connections. Unplug the base unit’s AC adapter to reset the unit, turn off the handset, reconnect the adapter, and turn the handset back on. Also, ensure the handset is registered to the base unit; if not, register it.
S
scotttaylorAug 27, 2025
How to fix Panasonic KX-TG2511CX Cordless Telephone when the handset does not ring?
- Z
  zwatsonAug 27, 2025
  If the handset does not ring on your Panasonic Cordless Telephone, the ringer volume may be turned off. Adjust the ringer volume to a suitable level.
E
ethompsonAug 29, 2025
Why is the handset display blank on my Panasonic Cordless Telephone?
- C
  clarkedwardAug 29, 2025
  If the handset display is blank on your Panasonic Cordless Telephone, turn the power on.
C
Cassandra RodriguezAug 31, 2025
Why I cannot make a call on my Panasonic KX-TG2511CX?
- C
  Cathy WattsAug 31, 2025
  If you cannot make a call on your Panasonic Cordless Telephone, the dialing mode may be set incorrectly; change the setting. Ensure the handset is not too far from the base unit. It is also possible that another unit or the answering system is currently in use; wait and try again later.
S
Stephanie OdomSep 1, 2025
Why is 'w' flashing on my Panasonic KX-TG2511CX?
- T
  Tonya TateSep 1, 2025
  If the 'w' icon is flashing on your Panasonic Cordless Telephone, it indicates that the handset is too far from the base unit. Try moving closer. Ensure that the base unit’s AC adapter is properly connected. Also, the handset may not be registered to the base unit; if this is the case, register it. Note that activating one-touch eco mode can reduce the range of the base unit in standby mode, so turn eco mode off if necessary.
G
Gary HollandSep 3, 2025
Why is caller information not displayed on my Panasonic KX-TG2511CX Cordless Telephone?
- T
  Tara WellsSep 3, 2025
  If caller information is not displayed on your Panasonic Cordless Telephone, ensure that you subscribe to a Caller ID service through your service provider. If the unit is connected to additional telephone equipment, remove it and plug the unit directly into the wall jack. If you use a DSL/ADSL service, connect a DSL/ADSL filter between the base unit and the telephone line jack. Also, other telephone equipment may be interfering with the unit; disconnect the other equipment and try again.
G
Garrett LucasSep 5, 2025
Why is caller information slow to display on my Panasonic KX-TG2511CX?
- P
  Paul TranSep 5, 2025
  If caller information is slow to display on your Panasonic Cordless Telephone, it may be due to your service provider displaying the information at the 2nd ring or later. Also, try moving closer to the base unit.

Panasonic KX-TG2511CX Specifications

General

Type	Cordless Telephone
Number of Handsets	1
Frequency	1.9 GHz
DECT	Yes
GAP compatible	Yes
Number of lines	1
Display	LCD
Display lines	1
Caller ID	Yes
Phonebook entries	50
Redial memory	10
Talk time	Up to 10 hours
Battery type	Ni-MH
Number of handsets supported	6
Answering Machine	No
Speakerphone	Yes
Power Source	AC Adapter
Range	Up to 300 meters outdoors, 50 meters indoors
Intercom	Yes