R
Robert ByrdAug 25, 2025
Why is my Panasonic Telephone handset beeping and/or flashing?
- WWendy GarciaAug 25, 2025
If your handset is beeping and/or flashing, it likely means the battery charge is low. You should fully charge the batteries.
To Next PageTo Next PageWhy is my Panasonic Telephone handset beeping and/or flashing?
If your handset is beeping and/or flashing, it likely means the battery charge is low. You should fully charge the batteries.
How to fix time shifting on my Panasonic Telephone?
If the time on your unit has shifted, it may be due to incorrect time information from incoming Caller ID. Set the time adjustment to “Manual” (off).
Why does my Panasonic Telephone unit not record new messages?
If the unit isn't recording new messages, consider the following: * The answering system is turned off. Turn it on. * The answering system does not answer or record calls from cellular lines. * The message memory is full. Erase unnecessary messages. * The recording time is set to “Greeting only”. Change the setting. * Your service provider/telephone company’s voice mail service may be answering your calls before the unit’s answering system can answer your calls. Change the unit’s number of rings setting to a lower value, or contact your service provider/telephone company. * The answering system will not answer incoming calls while the other devices such as headset or handsets are engaged in a call.
How to fix noise or sound cutting in and out on my Panasonic Telephone?
If you are experiencing noise or sound cutting in and out, the following might help: * If you're using the handset or base unit in an area with high electrical interference, reposition the base unit and use the handset away from sources of interference. * Move closer to the base unit. * If you use a DSL/ADSL service, consider connecting a DSL/ADSL filter between the base unit and the telephone line jack.
What to do if I cannot hear a dial tone on my Panasonic Telephone?
If you cannot hear a dial tone, check these: * Ensure the base unit’s AC adaptor and telephone line cord are properly connected. * Disconnect the base unit from the telephone line and connect the line to a known working telephone. If the working telephone operates properly, contact our service personnel to have the unit repaired. * If the working telephone does not operate properly, contact your service provider/telephone company.
Why doesn't my Panasonic Telephone handset or base unit ring?
If your handset or base unit isn't ringing, consider the following: * The ringer volume for landline might be turned off. Adjust the ringer volume. * The ringer volume for cellular line might be turned off. Adjust the ringer volume. * When one handset is selected to ring for cellular calls, other units do not ring. * Silent mode might be turned on. Turn it off.
What to do if caller information is not displayed on my Panasonic Telephone?
If caller information is not being displayed, consider these possible solutions: * Make sure you subscribe to Caller ID service. * If you are using additional telephone equipment, plug the unit directly into the wall jack. * If you use a DSL/ADSL service, connect a DSL/ADSL filter between the base unit and the telephone line jack. * The name display service for landline calls may not be available in some areas. * Other telephone equipment may be interfering with this unit. Disconnect the other equipment and try again.
Why is 'Voice mail msg. via phone co.' shown on my Panasonic Telephone display and how do I remove it?
This message appears when your service provider's voice mail service has a message for you, not your unit's answering system. Usually, you can clear it by listening to the message by dialing your voice mail number and following the instructions. You might need to clear all messages from your voice mailbox. Alternatively, press and hold the # key until the unit beeps to remove the notification.
Why is the handset display blank or dark on my Panasonic Telephone?
If your handset display is blank or dark, it could be due to these reasons: * The handset is in screen saver mode. To activate the display, press M N during a call or MOFFN at other times. * “LCD backlight” is set to “Off” while on charge. You can change this setting.
What to do if my Panasonic Telephone unit does not work?
If your unit isn't working, there are several things you can check: * Ensure the batteries are correctly installed. * Fully charge the batteries. * Verify all connections are secure. * Unplug the base unit’s AC adaptor to reset it, then reconnect and try again. * Make sure the handset is registered to the base unit.
General| GAP Compatible | Yes |
|---|---|
| Display | 1.8-inch LCD |
| Battery | Ni-MH rechargeable battery |
| Caller ID | Yes |
| Number of Handsets | 1 |
| Call Waiting | Yes |
| Intercom | Yes |
| Type | Cordless Handset |
| Compatibility | Compatible with Panasonic KX-TG series |
| Features | Intercom |
| Range | Up to 50 meters indoors |
| Phonebook Capacity | 100 |
| Headset Jack | Yes (2.5mm) |
