To Next PageTo Next PageWhy I cannot register a handset to a base unit on Panasonic KX-TGH720E?
If you cannot register a handset to a base unit on your Panasonic Cordless Telephone, it could be because the maximum number of base units (4) is already registered to the handset. Cancel unused base unit registrations from the handset. Also, ensure that you entered the correct PIN.
Why Panasonic KX-TGH720E handset beeps and/or flashes?
If your Panasonic Cordless Telephone handset beeps and/or flashes, it means the battery charge is low. You should fully charge the batteries.
Why I cannot hear a dial tone on my Panasonic KX-TGH720E Cordless Telephone?
If you cannot hear a dial tone on your Panasonic Cordless Telephone, ensure that you are using the supplied telephone line cord. Your old telephone line cord may have a different wiring configuration. Also, check that the base unit’s AC adapter or telephone line cord is connected. Disconnect the base unit from the telephone line and connect the line to a known working telephone. If the working telephone operates properly, contact our service personnel to have the unit repaired. If the working telephone does not operate properly, contact your phone service provider.
What to do if Panasonic Cordless Telephone handset display is blank or dark?
If the handset display is blank or dark on your Panasonic Cordless Telephone, it could be due to several reasons. The handset may be in screen saver mode. Activate the handset display again by pressing MCN when on a call, or pressing any dial key at all other times. Also, check if “LCD in charging” is set to “Off” while on charge, and change the setting if needed. Ensure the handset is turned on.
Why Panasonic KX-TGH720E handset does not ring?
If your Panasonic Cordless Telephone handset does not ring, check if the ringer volume is turned off and adjust it. Also, make sure the do not disturb mode is turned off. If the handset is registered to multiple base units, it may not be able to make or receive calls if Eco mode is set to “Eco Plus” and Base unit selection is set to “Auto”. In this case, place the handset near the base unit, and change the setting to “Eco” or “Off”. Repeat for each base unit.
Why I cannot operate the answering system remotely on my Panasonic KX-TGH720E?
If you cannot operate the answering system remotely on your Panasonic Cordless Telephone, ensure that the remote access code is set. Also, make sure you are entering the correct remote access code. If you have forgotten your remote access code, enter the remote access code setting to check your current code. Ensure that the answering system is turned on.
Why I cannot use the intercom feature on my Panasonic KX-TGH720E Cordless Telephone?
The intercom feature on your Panasonic Cordless Telephone is available between handsets. Although the handset displays “Intercom”, or “Auto Intercom”, these features are not available for single handset models.
Why I cannot activate the eco mode on my Panasonic KX-TGH720E Cordless Telephone?
You cannot set eco mode when you set the repeater mode “On”. If required, set the repeater mode to “Off”.
Why I cannot make a call on my Panasonic Cordless Telephone?
If you cannot make a call on your Panasonic Cordless Telephone, it might be because you dialled a call restricted number. Another possibility is that the key lock feature is turned on; turn it off.
Why Panasonic KX-TGH720E Cordless Telephone base unit beeps?
If your Panasonic Cordless Telephone base unit beeps, it indicates that new messages have been recorded. Listen to the new messages.
Lists model numbers, base unit and handset part numbers, and quantities for each series.
Details supplied accessories with part numbers and quantities, and additional/replacement accessories.
Covers design changes, illustration variations, and contact information for support.
Provides customer communication channels, website, and direct sales contact details.
Covers intended use, declaration of conformity, and ecodesign information for the product.
Explains common symbols used on the equipment and their corresponding meanings.
Recommends keeping product information for warranty and repair assistance.
Warns about potential hazards and advises careful reading for safe operation.
Details safe practices for connecting the power adaptor and avoiding electrical hazards.
Provides instructions and warnings for installing the telephone line cord and avoiding electrical shock.
Lists precautions for safe operation, including cleaning and disassembly.
Discusses RF energy shielding and usage considerations in healthcare facilities.
Advises on safe installation locations and connecting the AC adaptor.
Guides on using and handling rechargeable batteries, including warnings about mixing and short circuits.
Lists basic safety precautions for using the product, including water use and electrical storms.
Offers advice on base unit placement and environmental factors for optimal communication.
Details conditions to avoid, such as electrical noise, dust, high temperature, and vibration.
Provides instructions for cleaning the product's outer surface.
Warns about battery replacement risks and proper disposal methods.
Recommends erasing personal data before disposing of or transferring the product.
Explains the WEEE directive and proper disposal methods for electrical products and batteries.
Advises business users to contact their dealer for disposal information.
States that disposal symbols are only valid in the EU and advises contacting local authorities.
Explains the meaning of the battery symbol when combined with chemical symbols.
Refers to page 11 for battery removal instructions.
Specifies the wireless communication standard used by the unit (DECT, GAP).
Indicates the operating frequency range for the device.
Details the radio frequency transmission power levels of the unit.
Specifies the required power input for the unit.
Identifies the type and voltage of the rechargeable battery used.
Lists the power consumption for the base unit and charger in standby and maximum modes.
Outlines the recommended temperature and humidity ranges for operation.
Provides initial setup instructions for the device.
Details how to connect the base unit, charger, and telephone line.
Specific steps for connecting the base unit components.
Instructions for connecting the charger.
Guides on how to install the rechargeable batteries into the handset.
Instructions on how to remove the battery from the handset.
Explains the process and expected duration for charging the batteries.
Provides important notes regarding the setup and connection of the AC adaptor.
Offers specific advice on connecting the AC adaptor to outlets.
Advises on using a corded phone during a power outage.
Recommends using supplied rechargeable batteries for replacement.
Advises on cleaning contacts and notes that the handset may feel warm.
Shows icons representing different battery charge levels.
Details the operating time for Ni-MH batteries in continuous use and standby.
Identifies the buttons and controls on the base unit and handset.
Describes the controls located on the base unit.
Describes the controls and keys on the handset.
Explains various icons displayed on the handset and their meanings.
Lists and describes icons related to range, security, and modes shown on the handset.
Instructions on how to turn the handset power on and off.
Guides on how to change the display language of the unit.
Instructions for setting the current date and time on the unit.
Explains how to record a personalized greeting message for the answering system.
Covers additional settings like screen saver and eco mode.
Describes the screen saver function that dims or turns off the display.
Explains the power-saving Eco and Eco Plus modes and their effects.
Details the procedure for selecting the desired eco mode setting.
Provides instructions on how to initiate a phone call.
Explains how to change the volume level during a call.
Guides on redialing numbers from the stored redial list.
Instructions for deleting entries from the redial list.
Explains how to insert a pause when making calls with PBX or long distance services.
Details how to receive an incoming call using the handset or speakerphone.
Instructions on how to set the ringer volume for the handset.
Describes how to adjust the ringer volume on the base unit.
Covers features usable while a call is active.
Explains how to put an ongoing call on hold.
Instructions on how to mute the microphone during a call.
Describes the function of the Recall/flash key for PBX features.
Details how to handle call waiting and Caller ID information.
Explains how to adjust the sound quality for clearer calls.
Allows joining an existing outside call on compatible models.
Guides on transferring calls and setting up conference calls between units.
Describes how to make intercom calls between handsets.
Provides steps to initiate an intercom call.
Explains how to receive an intercom call.
Details how to enable automatic intercom answering.
Instructions on how to lock and unlock the handset keypad.
Explains how to block calls by adding numbers to a list.
Describes methods to block specific numbers, ranges, or withheld numbers.
Guides on adding specific phone numbers to the call block list.
Instructions to block numbers directly from the caller list.
Steps for manually entering numbers to be blocked.
How to block calls based on number ranges or prefixes.
How to block calls from callers with withheld or private numbers.
How to view and reset the count of blocked calls.
Procedures for managing entries in the call block list.
Steps to remove all entries from the call block list.
Explains how the unit screens calls and blocks automated ones.
Details the database for storing numbers that are allowed to pass through.
How to activate or deactivate the automated call block feature.
Procedure to change the access code for automated call block.
How to view and reset the count of blocked calls.
Allows specific callers to bypass the block by adding their name.
How to add names to the allow list from the caller list.
Procedures for viewing and deleting entries in the allow name list.
Steps to remove all entries from the allow name list.
Explains the greeting message played to callers during automated call block.
Guides on recording a custom greeting message.
How to revert to the default pre-recorded greeting message.
Instructions to play back the recorded or pre-recorded greeting message.
Details how to store up to 200 entries with names and phone numbers.
Step-by-step guide to add new contacts to the phonebook.
How to save numbers from the redial list into the phonebook.
Guide to saving incoming call information into the phonebook.
Explains how to organize phonebook entries into categories.
How to customize category names and assign specific ringer tones.
Steps to locate and dial contacts from the phonebook.
How to navigate through the entire phonebook list.
Method to find entries by starting with a specific letter.
How to narrow search results by entering initial characters of a name.
Method to find entries filtered by their assigned category.
Instructions for modifying existing phonebook entries.
Procedures for deleting entries from the phonebook.
Steps to delete a single phonebook entry.
How to remove all entries from the phonebook.
Allows dialing phone numbers from the phonebook while on an existing call.
How to assign numbers to speed dial and memory dial keys.
Guides on assigning numbers to speed dial and memory dial keys.
Steps to manually enter numbers for speed dial/memory dial.
How to assign phonebook entries to speed dial/memory dial keys.
Instructions for editing speed dial or memory dial entries.
Steps to delete speed dial or memory dial entries.
How to view and make calls using speed dial/memory dial.
Explains how to access features via menu scrolling or direct command codes.
Guides on navigating the device's menu system.
Instructions on using direct command codes to access features.
Provides a table of menu options and their corresponding command codes.
Configuration for alerts when new messages arrive.
General settings section for various functions.
Setting the number of rings before the answering system answers.
Adjusting the maximum recording time for messages.
Setting or managing the remote access code.
Option to listen to callers while they leave messages.
Turning the answering system on or off.
Section for managing date, time, and alarms.
Procedure to set the device's date and time.
Setting up memo alarms with text.
Setting time adjustment based on Caller ID or manual input.
Features related to making calls between handsets.
How to page a specific handset.
Configuring ringtones and volumes for different scenarios.
Setting the volume for external and intercom ringtones.
Selecting different ringtones for external and intercom calls.
Adjusting intercom ringer volume for the handset.
Selecting ringtones for external calls on the handset.
Selecting ringtones for intercom calls on the handset.
Setting periods when the handset will not ring for outside calls.
Setting the start and end times for Do Not Disturb mode.
Configuring a delay before ringing during Do Not Disturb mode.
Choosing categories that can bypass Do Not Disturb mode.
Setting whether the first ring is heard before or after caller ID information.
Managing settings for blocking unwanted calls.
Blocking specific phone numbers.
Blocking calls based on number prefixes or area codes.
Blocking calls with withheld or no number.
Viewing the total count of blocked calls.
Feature to listen to another room remotely.
Turning the Baby Monitor feature on or off.
Adjusting the sensitivity for the Baby Monitor feature.
Covers initial configuration options including ringers and time settings.
Section for configuring ringtones and volumes.
Setting the ringer volume for external calls on the handset.
Setting the ringer volume for external calls on the base unit.
Adjusting intercom ringer volume for the handset.
Selecting ringtones for external calls on the handset.
Selecting ringtones for intercom calls on the handset.
Setting periods when the handset will not ring for outside calls.
Setting the start and end times for Do Not Disturb mode.
Configuring a delay before ringing during Do Not Disturb mode.
Choosing categories that can bypass Do Not Disturb mode.
Setting whether the first ring is heard before or after caller ID information.
Section for managing date, time, and alarms.
Procedure to set the device's date and time.
Setting up memo alarms with text.
Setting time adjustment based on Caller ID or manual input.
Configuration for screening and blocking automated calls.
Setting the automated call block to block or allow calls.
Managing a list of names to bypass automated call blocking.
Setting or changing the access code for automated call block.
Setting up the greeting message for automated call block.
Managing settings for blocking unwanted calls.
Viewing the total count of blocked calls.
Blocking specific phone numbers.
Blocking calls based on number prefixes or area codes.
Blocking calls with withheld or no number.
Managing speed dial and memory dial entries.
Setting up speed dial numbers.
Configuring power-saving modes.
Enhancing security for phone conversations.
Recording a personalized greeting for the answering system.
Customizing display settings like wallpaper and clock.
Setting a custom wallpaper for the display.
Adjusting the clock display settings.
Changing the color scheme of the display.
Selecting how information is displayed on the screen.
Adjusting the backlight for the keypad.
Setting the display behavior while charging.
Customizing the name displayed for each handset.
Enabling or disabling the display of handset names.
Enabling or disabling automatic intercom calls.
Settings related to keypad tones.
Restricting specific numbers or area codes for certain handsets.
Enabling or disabling the auto talk feature.
Configuring line settings, including recall/flash times.
Setting the recall/flash time for PBX or telephone exchange features.
Enhancing conversation security by preventing others from joining calls.
Setting or changing the PIN for base unit access.
Enabling or disabling the repeater mode for extended range.
Procedures for registering new handsets or base units.
Step-by-step guide to register a handset to the base unit.
How to cancel the registration of a handset or base unit.
Choosing the base unit for handset operation.
Cancelling the registration of a base unit from a handset.
Changing the display language of the unit.
General display setting options.
Viewing entries stored in memory dial.
Setting up alarms with time, text memo, and snooze function.
Reminder to ensure date and time are set correctly before configuring alarms.
Choosing which alarm to set or modify.
Choosing the alarm type: Off, Once, Daily, or Weekly.
Option to turn off an alarm.
Setting an alarm to sound only one time.
Setting an alarm to sound every day.
Setting an alarm to sound on specific days of the week.
General instruction to follow for setting alarm times and dates.
Specific instruction for setting a one-time alarm date.
Specific instruction for setting alarm days for weekly alarms.
Setting the specific time for the alarm to sound.
Adding a text note to be displayed with the alarm.
Choosing the sound for the alarm.
Setting periods when the handset will not ring for outside calls.
Activating or deactivating the Do Not Disturb mode.
Setting the specific hours for the Do Not Disturb mode.
Configuring a delay before ringing during Do Not Disturb mode.
Choosing categories of callers that can ring during Do Not Disturb.
Feature to listen to another room remotely.
How to use the baby monitor feature between handsets in the same radio cell.
Setting up the baby monitor to call an external number when sound is detected.
Manually entering phone numbers for remote baby monitor calls.
Disabling the baby monitor feature.
Modifying phone numbers for remote baby monitor calls.
Removing phone numbers for remote baby monitor calls.
Adjusting the sensitivity level for the baby monitor feature.
How to answer calls initiated by the baby monitor feature.
Answering baby monitor calls made between handsets.
Answering baby monitor calls made to an external number.
Miscellaneous programming options.
Customizing the name displayed for each handset.
Selecting whether handset names are displayed in standby mode.
Restricting specific numbers or area codes for certain handsets.
Setting enhanced security for conversations to prevent eavesdropping.
Procedures for changing the base unit's Personal Identification Number.
Adding new handsets or base units to the system.
Information on adding extra base units to extend coverage.
How to pair a handset with the base unit.
Choosing the base unit for handset operation, including 'Auto' mode.
Key considerations before registering a repeater.
Removing a handset's registration from the base unit.
Ending a base unit's wireless connection with the system.
Using a DECT repeater to extend the wireless range.
Enabling or disabling the repeater mode for range extension.
Steps to register a DECT repeater with the base unit.
How to subscribe to and utilize Caller ID features.
Note about ensuring date/time are set correctly for Caller ID.
Details on how caller information is displayed and logged.
How missed calls are indicated and viewed.
Displaying contact names from the phonebook when Caller ID matches.
Information on the list of incoming calls and how to view it.
Reminder to ensure date and time settings are correct for the caller list.
Steps to view call history and redial numbers.
Modifying phone numbers stored in the caller list.
Deleting individual entries from the caller list.
Procedures for clearing all entries from the caller list.
Overview of the answering system's functions for recording calls.
Note to ensure date and time settings are correct for the answering system.
Information on the total recording time and message capacity.
Notes on memory full status and message display.
How to activate or deactivate the answering system.
Instructions for turning the answering system on/off using the base unit.
Instructions for turning the answering system on/off using the handset.
Notes regarding the message counter and display when the system is on.
Explains the types of greeting messages available.
Step-by-step guide to record a personalized greeting.
Information about the unit's built-in pre-recorded greeting messages.
How to erase your greeting and use the pre-recorded one.
Instructions to play back the greeting message.
How to access and play recorded messages.
Procedures for listening to messages using the base unit controls.
Controls available during message playback (volume, repeat, skip, stop, erase).
How to rewind through a recorded message.
How to fast-forward through a recorded message.
Procedure to delete all recorded messages.
How to listen to messages using the handset controls.
Selecting and playing messages from a list on the handset.
Deleting specific entries from the caller list.
How to call back a number from the caller list.
Modifying a caller's number before initiating a callback.
Procedure to delete all recorded messages.
Features for notifying users of new messages.
Setting the base unit to beep when new messages arrive.
Setting the unit to call a specified number to notify of new messages.
Setting a phone number for new message alert notifications.
Selecting a number from the phonebook for alert calls.
Manually entering a number for alert calls.
Activating or deactivating the new message alert feature.
Modifying the phone number for new message alerts.
Removing the phone number for new message alerts.
Setting whether a remote access code is needed to play messages.
How to listen to messages after receiving a new message alert.
Accessing the answering system remotely via a phone.
Setting and using a 3-digit code for remote access security.
Prerequisite to set a remote access code before remote operation.
Procedure to disable remote operation and delete the access code.
Step-by-step guide to operate the answering system from an external phone.
Explains the voice prompts used during remote operation.
List of dial keys for direct control of the answering system remotely.
Setting how many times the phone rings before the unit answers.
Adjusting the maximum recording duration per caller.
Setting the unit to only announce a greeting without recording messages.
Information on using voicemail from a phone service provider.
Note on turning off the unit's answering system to use voicemail.
Explains how to enter characters and numbers using the dial keys.
Details the different modes available for entering characters (Alphabet, Numeric, etc.).
Lists common error messages and their causes/solutions.
Describes messages displayed on the unit and their troubleshooting steps.
Troubleshooting steps for power or connection issues.
Checks related to the telephone line connection.
Notes on the automated call block function.
Specific error messages like recording too short.
Solutions for full memory in phonebook, call block, or base units.
Advice regarding the correct type of batteries to use.
Requirement to subscribe to Caller ID service for certain features.
Common problems and solutions for general operation.
Common problems and solutions for general operation.
Troubleshooting steps if the handset fails to power on.
Solutions for when the entire unit is unresponsive.
Steps to resolve issues with a blank or dark handset display.
Troubleshooting for absence of dial tone.
Explains the cause for the base unit beeping (new messages).
How to turn off demonstration mode if the display activates unexpectedly.
Troubleshooting for error sounds when pressing keys.
Reasons why the intercom feature might not be available.
Explains why the number of rings may differ from the setting.
Troubleshooting for issues with the menu display language.
Steps to change the display language if it's unreadable.
Reasons why eco mode might not be selectable, e.g., with repeater mode.
Troubleshooting steps for failed handset registration.
Instructions on how to change the PIN if it's forgotten.
Troubleshooting for battery charging issues.
Indicates low battery charge or issues with charging.
Advice for batteries that still flash or have reduced operating time after charging.
Explains the meaning of the display indicating handset distance or connection issues.
Troubleshooting steps for poor audio quality or interference.
Advice on improving sound quality, possibly by registering the correct handset.
Reasons why the handset might not ring, like ringer volume or Do Not Disturb mode.
Troubleshooting for the base unit not ringing.
Reasons for being unable to make calls, e.g., call restriction or key lock.
Troubleshooting for Caller ID related issues.
Steps to resolve issues where Caller ID information is not shown.
Factors affecting the speed of Caller ID display.
How to correct time shifts, possibly related to Caller ID data.
Solutions for the answering system not recording messages.
Troubleshooting for remote operation issues, like forgotten codes.
Instructions for dealing with moisture damage to the unit.
Details the terms and conditions of the product's warranty.
Lists model numbers, base unit and handset part numbers, and quantities for each series.
Details supplied accessories with part numbers and quantities, and additional/replacement accessories.
Covers design changes, illustration variations, and contact information for support.
Provides customer communication channels, website, and direct sales contact details.
Covers intended use, declaration of conformity, and ecodesign information for the product.
Explains common symbols used on the equipment and their corresponding meanings.
Recommends keeping product information for warranty and repair assistance.
Warns about potential hazards and advises careful reading for safe operation.
Details safe practices for connecting the power adaptor and avoiding electrical hazards.
Provides instructions and warnings for installing the telephone line cord and avoiding electrical shock.
Lists precautions for safe operation, including cleaning and disassembly.
Discusses RF energy shielding and usage considerations in healthcare facilities.
Advises on safe installation locations and connecting the AC adaptor.
Guides on using and handling rechargeable batteries, including warnings about mixing and short circuits.
Lists basic safety precautions for using the product, including water use and electrical storms.
Offers advice on base unit placement and environmental factors for optimal communication.
Details conditions to avoid, such as electrical noise, dust, high temperature, and vibration.
Provides instructions for cleaning the product's outer surface.
Warns about battery replacement risks and proper disposal methods.
Recommends erasing personal data before disposing of or transferring the product.
Explains the WEEE directive and proper disposal methods for electrical products and batteries.
Advises business users to contact their dealer for disposal information.
States that disposal symbols are only valid in the EU and advises contacting local authorities.
Explains the meaning of the battery symbol when combined with chemical symbols.
Refers to page 11 for battery removal instructions.
Specifies the wireless communication standard used by the unit (DECT, GAP).
Indicates the operating frequency range for the device.
Details the radio frequency transmission power levels of the unit.
Specifies the required power input for the unit.
Identifies the type and voltage of the rechargeable battery used.
Lists the power consumption for the base unit and charger in standby and maximum modes.
Outlines the recommended temperature and humidity ranges for operation.
Provides initial setup instructions for the device.
Details how to connect the base unit, charger, and telephone line.
Specific steps for connecting the base unit components.
Instructions for connecting the charger.
Guides on how to install the rechargeable batteries into the handset.
Instructions on how to remove the battery from the handset.
Explains the process and expected duration for charging the batteries.
Provides important notes regarding the setup and connection of the AC adaptor.
Offers specific advice on connecting the AC adaptor to outlets.
Advises on using a corded phone during a power outage.
Recommends using supplied rechargeable batteries for replacement.
Advises on cleaning contacts and notes that the handset may feel warm.
Shows icons representing different battery charge levels.
Details the operating time for Ni-MH batteries in continuous use and standby.
Identifies the buttons and controls on the base unit and handset.
Describes the controls located on the base unit.
Describes the controls and keys on the handset.
Explains various icons displayed on the handset and their meanings.
Lists and describes icons related to range, security, and modes shown on the handset.
Instructions on how to turn the handset power on and off.
Guides on how to change the display language of the unit.
Instructions for setting the current date and time on the unit.
Explains how to record a personalized greeting message for the answering system.
Covers additional settings like screen saver and eco mode.
Describes the screen saver function that dims or turns off the display.
Explains the power-saving Eco and Eco Plus modes and their effects.
Details the procedure for selecting the desired eco mode setting.
Provides instructions on how to initiate a phone call.
Explains how to change the volume level during a call.
Guides on redialing numbers from the stored redial list.
Instructions for deleting entries from the redial list.
Explains how to insert a pause when making calls with PBX or long distance services.
Details how to receive an incoming call using the handset or speakerphone.
Instructions on how to set the ringer volume for the handset.
Describes how to adjust the ringer volume on the base unit.
Covers features usable while a call is active.
Explains how to put an ongoing call on hold.
Instructions on how to mute the microphone during a call.
Describes the function of the Recall/flash key for PBX features.
Details how to handle call waiting and Caller ID information.
Explains how to adjust the sound quality for clearer calls.
Allows joining an existing outside call on compatible models.
Guides on transferring calls and setting up conference calls between units.
Describes how to make intercom calls between handsets.
Provides steps to initiate an intercom call.
Explains how to receive an intercom call.
Details how to enable automatic intercom answering.
Instructions on how to lock and unlock the handset keypad.
Explains how to block calls by adding numbers to a list.
Describes methods to block specific numbers, ranges, or withheld numbers.
Guides on adding specific phone numbers to the call block list.
Instructions to block numbers directly from the caller list.
Steps for manually entering numbers to be blocked.
How to block calls based on number ranges or prefixes.
How to block calls from callers with withheld or private numbers.
How to view and reset the count of blocked calls.
Procedures for managing entries in the call block list.
Steps to remove all entries from the call block list.
Explains how the unit screens calls and blocks automated ones.
Details the database for storing numbers that are allowed to pass through.
How to activate or deactivate the automated call block feature.
Procedure to change the access code for automated call block.
How to view and reset the count of blocked calls.
Allows specific callers to bypass the block by adding their name.
How to add names to the allow list from the caller list.
Procedures for viewing and deleting entries in the allow name list.
Steps to remove all entries from the allow name list.
Explains the greeting message played to callers during automated call block.
Guides on recording a custom greeting message.
How to revert to the default pre-recorded greeting message.
Instructions to play back the recorded or pre-recorded greeting message.
Details how to store up to 200 entries with names and phone numbers.
Step-by-step guide to add new contacts to the phonebook.
How to save numbers from the redial list into the phonebook.
Guide to saving incoming call information into the phonebook.
Explains how to organize phonebook entries into categories.
How to customize category names and assign specific ringer tones.
Steps to locate and dial contacts from the phonebook.
How to navigate through the entire phonebook list.
Method to find entries by starting with a specific letter.
How to narrow search results by entering initial characters of a name.
Method to find entries filtered by their assigned category.
Instructions for modifying existing phonebook entries.
Procedures for deleting entries from the phonebook.
Steps to delete a single phonebook entry.
How to remove all entries from the phonebook.
Allows dialing phone numbers from the phonebook while on an existing call.
How to assign numbers to speed dial and memory dial keys.
Guides on assigning numbers to speed dial and memory dial keys.
Steps to manually enter numbers for speed dial/memory dial.
How to assign phonebook entries to speed dial/memory dial keys.
Instructions for editing speed dial or memory dial entries.
Steps to delete speed dial or memory dial entries.
How to view and make calls using speed dial/memory dial.
Explains how to access features via menu scrolling or direct command codes.
Guides on navigating the device's menu system.
Instructions on using direct command codes to access features.
Provides a table of menu options and their corresponding command codes.
Configuration for alerts when new messages arrive.
General settings section for various functions.
Setting the number of rings before the answering system answers.
Adjusting the maximum recording time for messages.
Setting or managing the remote access code.
Option to listen to callers while they leave messages.
Turning the answering system on or off.
Section for managing date, time, and alarms.
Procedure to set the device's date and time.
Setting up memo alarms with text.
Setting time adjustment based on Caller ID or manual input.
Features related to making calls between handsets.
How to page a specific handset.
Configuring ringtones and volumes for different scenarios.
Setting the volume for external and intercom ringtones.
Selecting different ringtones for external and intercom calls.
Adjusting intercom ringer volume for the handset.
Selecting ringtones for external calls on the handset.
Selecting ringtones for intercom calls on the handset.
Setting periods when the handset will not ring for outside calls.
Setting the start and end times for Do Not Disturb mode.
Configuring a delay before ringing during Do Not Disturb mode.
Choosing categories that can bypass Do Not Disturb mode.
Setting whether the first ring is heard before or after caller ID information.
Managing settings for blocking unwanted calls.
Blocking specific phone numbers.
Blocking calls based on number prefixes or area codes.
Blocking calls with withheld or no number.
Viewing the total count of blocked calls.
Feature to listen to another room remotely.
Turning the Baby Monitor feature on or off.
Adjusting the sensitivity for the Baby Monitor feature.
Covers initial configuration options including ringers and time settings.
Section for configuring ringtones and volumes.
Setting the ringer volume for external calls on the handset.
Setting the ringer volume for external calls on the base unit.
Adjusting intercom ringer volume for the handset.
Selecting ringtones for external calls on the handset.
Selecting ringtones for intercom calls on the handset.
Setting periods when the handset will not ring for outside calls.
Setting the start and end times for Do Not Disturb mode.
Configuring a delay before ringing during Do Not Disturb mode.
Choosing categories that can bypass Do Not Disturb mode.
Setting whether the first ring is heard before or after caller ID information.
Section for managing date, time, and alarms.
Procedure to set the device's date and time.
Setting up memo alarms with text.
Setting time adjustment based on Caller ID or manual input.
Configuration for screening and blocking automated calls.
Setting the automated call block to block or allow calls.
Managing a list of names to bypass automated call blocking.
Setting or changing the access code for automated call block.
Setting up the greeting message for automated call block.
Managing settings for blocking unwanted calls.
Viewing the total count of blocked calls.
Blocking specific phone numbers.
Blocking calls based on number prefixes or area codes.
Blocking calls with withheld or no number.
Managing speed dial and memory dial entries.
Setting up speed dial numbers.
Configuring power-saving modes.
Enhancing security for phone conversations.
Recording a personalized greeting for the answering system.
Customizing display settings like wallpaper and clock.
Setting a custom wallpaper for the display.
Adjusting the clock display settings.
Changing the color scheme of the display.
Selecting how information is displayed on the screen.
Adjusting the backlight for the keypad.
Setting the display behavior while charging.
Customizing the name displayed for each handset.
Enabling or disabling the display of handset names.
Enabling or disabling automatic intercom calls.
Settings related to keypad tones.
Restricting specific numbers or area codes for certain handsets.
Enabling or disabling the auto talk feature.
Configuring line settings, including recall/flash times.
Setting the recall/flash time for PBX or telephone exchange features.
Enhancing conversation security by preventing others from joining calls.
Setting or changing the PIN for base unit access.
Enabling or disabling the repeater mode for extended range.
Procedures for registering new handsets or base units.
Step-by-step guide to register a handset to the base unit.
How to cancel the registration of a handset or base unit.
Choosing the base unit for handset operation.
Cancelling the registration of a base unit from a handset.
Changing the display language of the unit.
General display setting options.
Viewing entries stored in memory dial.
Setting up alarms with time, text memo, and snooze function.
Reminder to ensure date and time are set correctly before configuring alarms.
Choosing which alarm to set or modify.
Choosing the alarm type: Off, Once, Daily, or Weekly.
Option to turn off an alarm.
Setting an alarm to sound only one time.
Setting an alarm to sound every day.
Setting an alarm to sound on specific days of the week.
General instruction to follow for setting alarm times and dates.
Specific instruction for setting a one-time alarm date.
Specific instruction for setting alarm days for weekly alarms.
Setting the specific time for the alarm to sound.
Adding a text note to be displayed with the alarm.
Choosing the sound for the alarm.
Setting periods when the handset will not ring for outside calls.
Activating or deactivating the Do Not Disturb mode.
Setting the specific hours for the Do Not Disturb mode.
Configuring a delay before ringing during Do Not Disturb mode.
Choosing categories of callers that can ring during Do Not Disturb.
Feature to listen to another room remotely.
How to use the baby monitor feature between handsets in the same radio cell.
Setting up the baby monitor to call an external number when sound is detected.
Manually entering phone numbers for remote baby monitor calls.
Disabling the baby monitor feature.
Modifying phone numbers for remote baby monitor calls.
Removing phone numbers for remote baby monitor calls.
Adjusting the sensitivity level for the baby monitor feature.
How to answer calls initiated by the baby monitor feature.
Answering baby monitor calls made between handsets.
Answering baby monitor calls made to an external number.
Miscellaneous programming options.
Customizing the name displayed for each handset.
Selecting whether handset names are displayed in standby mode.
Restricting specific numbers or area codes for certain handsets.
Setting enhanced security for conversations to prevent eavesdropping.
Procedures for changing the base unit's Personal Identification Number.
Adding new handsets or base units to the system.
Information on adding extra base units to extend coverage.
How to pair a handset with the base unit.
Choosing the base unit for handset operation, including 'Auto' mode.
Key considerations before registering a repeater.
Removing a handset's registration from the base unit.
Ending a base unit's wireless connection with the system.
Using a DECT repeater to extend the wireless range.
Enabling or disabling the repeater mode for range extension.
Steps to register a DECT repeater with the base unit.
How to subscribe to and utilize Caller ID features.
Note about ensuring date/time are set correctly for Caller ID.
Details on how caller information is displayed and logged.
How missed calls are indicated and viewed.
Displaying contact names from the phonebook when Caller ID matches.
Information on the list of incoming calls and how to view it.
Reminder to ensure date and time settings are correct for the caller list.
Steps to view call history and redial numbers.
Modifying phone numbers stored in the caller list.
Deleting individual entries from the caller list.
Procedures for clearing all entries from the caller list.
Overview of the answering system's functions for recording calls.
Note to ensure date and time settings are correct for the answering system.
Information on the total recording time and message capacity.
Notes on memory full status and message display.
How to activate or deactivate the answering system.
Instructions for turning the answering system on/off using the base unit.
Instructions for turning the answering system on/off using the handset.
Notes regarding the message counter and display when the system is on.
Explains the types of greeting messages available.
Step-by-step guide to record a personalized greeting.
Information about the unit's built-in pre-recorded greeting messages.
How to erase your greeting and use the pre-recorded one.
Instructions to play back the greeting message.
How to access and play recorded messages.
Procedures for listening to messages using the base unit controls.
Controls available during message playback (volume, repeat, skip, stop, erase).
How to rewind through a recorded message.
How to fast-forward through a recorded message.
Procedure to delete all recorded messages.
How to listen to messages using the handset controls.
Selecting and playing messages from a list on the handset.
Deleting specific entries from the caller list.
How to call back a number from the caller list.
Modifying a caller's number before initiating a callback.
Procedure to delete all recorded messages.
Features for notifying users of new messages.
Setting the base unit to beep when new messages arrive.
Setting the unit to call a specified number to notify of new messages.
Setting a phone number for new message alert notifications.
Selecting a number from the phonebook for alert calls.
Manually entering a number for alert calls.
Activating or deactivating the new message alert feature.
Modifying the phone number for new message alerts.
Removing the phone number for new message alerts.
Setting whether a remote access code is needed to play messages.
How to listen to messages after receiving a new message alert.
Accessing the answering system remotely via a phone.
Setting and using a 3-digit code for remote access security.
Prerequisite to set a remote access code before remote operation.
Procedure to disable remote operation and delete the access code.
Step-by-step guide to operate the answering system from an external phone.
Explains the voice prompts used during remote operation.
List of dial keys for direct control of the answering system remotely.
Setting how many times the phone rings before the unit answers.
Adjusting the maximum recording duration per caller.
Setting the unit to only announce a greeting without recording messages.
Information on using voicemail from a phone service provider.
Note on turning off the unit's answering system to use voicemail.
Explains how to enter characters and numbers using the dial keys.
Details the different modes available for entering characters (Alphabet, Numeric, etc.).
Lists common error messages and their causes/solutions.
Describes messages displayed on the unit and their troubleshooting steps.
Troubleshooting steps for power or connection issues.
Checks related to the telephone line connection.
Notes on the automated call block function.
Specific error messages like recording too short.
Solutions for full memory in phonebook, call block, or base units.
Advice regarding the correct type of batteries to use.
Requirement to subscribe to Caller ID service for certain features.
Common problems and solutions for general operation.
Common problems and solutions for general operation.
Troubleshooting steps if the handset fails to power on.
Solutions for when the entire unit is unresponsive.
Steps to resolve issues with a blank or dark handset display.
Troubleshooting for absence of dial tone.
Explains the cause for the base unit beeping (new messages).
How to turn off demonstration mode if the display activates unexpectedly.
Troubleshooting for error sounds when pressing keys.
Reasons why the intercom feature might not be available.
Explains why the number of rings may differ from the setting.
Troubleshooting for issues with the menu display language.
Steps to change the display language if it's unreadable.
Reasons why eco mode might not be selectable, e.g., with repeater mode.
Troubleshooting steps for failed handset registration.
Instructions on how to change the PIN if it's forgotten.
Troubleshooting for battery charging issues.
Indicates low battery charge or issues with charging.
Advice for batteries that still flash or have reduced operating time after charging.
Explains the meaning of the display indicating handset distance or connection issues.
Troubleshooting steps for poor audio quality or interference.
Advice on improving sound quality, possibly by registering the correct handset.
Reasons why the handset might not ring, like ringer volume or Do Not Disturb mode.
Troubleshooting for the base unit not ringing.
Reasons for being unable to make calls, e.g., call restriction or key lock.
Troubleshooting for Caller ID related issues.
Steps to resolve issues where Caller ID information is not shown.
Factors affecting the speed of Caller ID display.
How to correct time shifts, possibly related to Caller ID data.
Solutions for the answering system not recording messages.
Troubleshooting for remote operation issues, like forgotten codes.
Instructions for dealing with moisture damage to the unit.
Details the terms and conditions of the product's warranty.
General| Type | Cordless Telephone |
|---|---|
| Number of Handsets Included | 1 |
| Maximum Number of Handsets | 6 |
| Display | LCD |
| Standby Time | 200 hours |
| Caller ID | Yes |
| Speakerphone | Yes |
| DECT Technology | Yes |
| GAP Compatible | Yes |
| Answering Machine | Yes |
| Frequency | 1.9 GHz |
| Range (Outdoors) | 300 meters |
| Call Waiting | Yes |
| Conference Call | Yes |
| Intercom | Yes |
| Headset Jack | Yes |
| Power Backup | No |
| Weight (Handset) | 120 grams |
