Panasonic NV-DV2000EC - One-Touch Insert and Audio Dubbing; One-Touch Insert and Audio Dubbing Steps; One-Touch Audio Dubbing Notes

For Quick Editing
41
One-Touch Insert/Audio Dubbing
If the One-Touch Edit functions is used, Insert (Video Insert, Audio Insert, and AV Insert) and Audio Dubbing can be
performed by controlling the playback unit through the NV-DV2000.
Preparations
¡ Confirm that the TV is on and the VCR viewing
channel is selected.
¡ Complete necessary connections and settings.
[R28–35]
¡ Set One-Touch-Edit to ON on Edit functions menu.
[R37]
Operations
1 Press JOG/SHUTTLE on the Editing controller, and
check that the button is lit.
2 Search for the edit start point on the recording
VCR.
3 Press the button for the editing mode on the Editing
controller.
To insert picture: Press VIDEO
INSERT.
To insert sound: Press AUDIO
INSERT.
To insert picture and sound: Press
VIDEO INSERT and then press
AUDIO INSERT (or vice versa).
To add new sound: Press AUDIO
DUB.
≥ The picture from the playback
unit appears on the screen.
4 Search for the edit start point on the playback unit.
5 Press JOG/SHUTTLE on the Editing controller.
≥ Editing begins.
≥ To continue editing, press JOG/SHUTTLE on the
Editing controller, and repeat steps 4–5.
6 Press ∫ (STOP) on the Editing controller to stop
editing.
< EJECT
AUDIO
OUT
REW STOP
PLAY FF PAUSE
STEREO
SERECT
DV IN/OUT DV SELECT
1
2
EDIT 8mm CONTROL
¥
AV4
OUT
AV4
EDIT CONTROL
RECORDER
PRINTER/
D.STILL PICTURE
PLAYER PASSIVE EDIT
DV
8mm
CONTROL
SP/LP TBC 3D NR PRINT
AUDIO REC LEVEL
AUDIO MIX
STILL
ALBUM
INPUT SELECT
010
STEREO1
STEREO1 STEREO2
100
¥ REC / OTR
MIXING EDIT
MIXING EDIT
DIGITAL VCR
1,5
3
6
2,4
S-VIDEO
VIDEO
L– AUDIO – R
To Listen to the Edited Audio After Audio
Dubbing
Press STEREO SELECT during playback and select
STEREO2.
Notes:
¡ Video Insert and Audio Insert are not possible in
the following cases:
When the tape in the recording VCR (the NV-DV2000)
is:
Recorded in LP mode;
Blank, or contains a blank portion in the middle.
¡ AV Insert and Audio Dubbing are not possible in
the following cases:
When the tape in the recording VCR (the NV-DV2000)
is:
Recorded in 16bit audio mode;
Recorded in LP mode;
Blank, or contains a blank portion in the middle.
When INPUT SELECT is set to DV1 or DV2.
¡ If the time display on the NV-DV2000 is set to tape
counter mode during editing, the NV-DV2000 stops
the editing operation automatically when the counter
reaches “0:00.00”.
¡ In order to ensure that the editing operation is
performed properly, the editing points should be set at
least 20 seconds after the beginning of the tape.
¡ When using the Editing controller for remote control:
In order to conserve battery power, JOG/SHUTTLE
turns off after 30 seconds.
If JOG/SHUTTLE turns off after the edit start point
has been set on the recording unit (step 2), it is
necessary to press JOG/SHUTTLE again (so that it is
lit) before searching for the edit start point on the
playback unit.
If JOG/SHUTTLE turns off after the edit start point
has been determined on the playback unit (step 4), it
is necessary to press JOG/SHUTTLE again in order
to start editing.
ST1
ST1
TBC
V INSERT
ST1
ST1
A INSERT
ST1
ST1
AV INSERT
ST 2
ST12
A DUB
L
R
dB -¶ 30 20 10 5 0 OVER
l l l l l l l l
l l l l l l l l l
ST 2
ST1 2