To Next PageTo Next PageWhy is the image stretched on my Panasonic PT-CX300?
If the image is stretched on your Panasonic Projector due to different video sources, when the video source is 16:9, adjust [16:9] in [Aspect Ratio] in the [Position] menu. When the video source is 4:3, adjust [4:3] in [Aspect Ratio] in the [Position] menu. If the image remains stretched after the previous settings, please adjust the aspect ratio of the player.
What to do if no picture appears on Panasonic PT-CX300 Projector?
If you're not getting any picture on your Panasonic Projector, first, reconnect the video signal input source to ensure it's properly connected to a terminal. Then, adjust the input selection setting to the correct source. Increase the [Brightness] adjustment setting if it's at the minimum. Check the input source for any issues. Finally, turn off the [AV mute] function if it's in use.
Why does the remote control not operate my Panasonic Projector?
If your Panasonic Projector remote control isn't working, try replacing the remote control battery first. If that doesn't work, check the battery installation to ensure it's correct. Make sure there are no obstructions blocking the remote control signal receptor on the projector. Also, ensure that you are within the remote control's operation range by moving closer to the projector. Reduce strong light shining onto the signal receptor. Finally, ensure matching remote IDs on projector and remote.
How to correct reversed image on Panasonic PT-CX300?
If the image on your Panasonic Projector is reversed, confirm [Ceiling Mount] in the [Position] menu.
What to do if messages display on Panasonic PT-CX300 Projector?
If your Panasonic Projector displays a message, it could be due to several reasons. A 'Dust Filter Reminder Message' indicates that the projector has reached the timer set in the [Filter Reminder (Hour)], suggesting that you should clean or replace the air filters. A 'Lamp Warning Message' means the lamp has reached its end of life and should be replaced as soon as possible. A 'Fan Locked Warning Message' indicates the fan has stopped during projection, in which case you should unplug the power cord and contact your dealer. Lastly, a 'Temperature Fail Message' means the internal temperature is too high, and you should confirm the display items.
How to restore sound to my Panasonic Projector internal speaker?
If there's no sound from the internal speaker of your Panasonic Projector, first, reconnect the input terminals to ensure they are correctly connected. Then, increase the volume level if it's set to the minimum. Also, turn off the [AV mute] function if it's on. Disconnect the VARIABLE AUDIO OUT, as the projector's built-in speaker is not available when it is plugged in. Finally, disable the Mute function if it's enabled.
What does it mean if my Panasonic Projector lamp burns out?
If the lamp burns out or makes a popping sound in your Panasonic Projector, the projector will not turn on until the lamp module has been replaced.
What to do if Panasonic PT-CX300 Projector image is too small?
If the image on your Panasonic Projector is too small or too large, move the projector closer to or further from the screen. You can also confirm [Aspect Ratio] in the [Position] menu.
How to remove vertical lines from Panasonic PT-CX300 image?
If you see vertical lines on the image from your Panasonic Projector, adjust [Clock] in the [Position] menu.
Why can't I adjust the [Picture] menu on my Panasonic PT-CX300 Projector?
If the [Picture] menu on your Panasonic Projector cannot be adjusted, switch the [3D] setting to [On].
General| Brightness | 3000 lumens |
|---|---|
| Resolution | XGA (1024 x 768) |
| Contrast Ratio | 2000:1 |
| Display Type | 3LCD |
| Screen Size | 30 - 300 inches |
| Output Terminals | VGA |
| Lamp Life | 5000 hours (Eco mode) |
| Lamp Type | UHM |
| Input Terminals | HDMI, VGA, Composite Video |
| Noise Level | 29 dB (Eco mode) |
