Panasonic PT-RW730

Chapter 4 Settings — [PROJECTOR SETUP] menu
120 - ENGLISH
f To set the projector based on luminance
Luminance (lm)
When [CONSTANT MODE] is set to [OFF] When [CONSTANT MODE] is set to [AUTO] or [PC]
[MAX LIGHT
OUTPUT LEVEL]
(%)
[LIGHT OUTPUT]
(%)
Runtime (hour)
[MAX LIGHT
OUTPUT LEVEL]
(%)
[LIGHT OUTPUT]
(%)
Runtime (hour)
7 000 100.0 100.0 20 000 ― ― ―
6 500 100.0 93.0 22 000 100.0 ― ―
6 000 100.0 86.0 23 500 100.0 86.0 3 000
5 500 100.0 79.0 25 000 100.0 79.0 6 000
5 000 100.0 71.0 26 500 100.0 71.0 9 000
4 500 100.0 64.0 28 000 100.0 64.0 12 500
4 000 100.0 57.0 30 000 100.0 57.0 17 000
3 500 100.0 50.0 31 500 100.0 50.0 22 500
3 000 100.0 43.0 33 000 100.0 43.0 28 500
2 500 100.0 36.0 34 500 100.0 36.0 36 000
r PT-RZ660/PT-RW620
f To set the projector based on the duration of use
Duration of use
(hour)
When [CONSTANT MODE] is set to [OFF] When [CONSTANT MODE] is set to [AUTO] or [PC]
[MAX LIGHT
OUTPUT LEVEL]
(%)
[LIGHT OUTPUT]
(%)
Luminance (lm)
[MAX LIGHT
OUTPUT LEVEL]
(%)
[LIGHT OUTPUT]
(%)
Luminance (lm)
20 000 100.0 100.0 6 000 100.0 53.0 3 200
24 000 100.0 83.0 5 000 100.0 48.0 2 900
27 000 100.0 70.0 4 200 100.0 45.0 2 700
31 000 100.0 53.0 3 200 100.0 40.0 2 400
35 000 100.0 33.0 2 000 100.0 37.0 2 200
40 000 ― ― ― 100.0 33.0 2 000
f To set the projector based on luminance
Luminance (lm)
When [CONSTANT MODE] is set to [OFF] When [CONSTANT MODE] is set to [AUTO] or [PC]
[MAX LIGHT
OUTPUT LEVEL]
(%)
[LIGHT OUTPUT]
(%)
Runtime (hour)
[MAX LIGHT
OUTPUT LEVEL]
(%)
[LIGHT OUTPUT]
(%)
Runtime (hour)
6 000 100.0 100.0 20 000 ― ― ―
5 500 100.0 92.0 22 000 100.0 ― ―
5 000 100.0 83.0 24 000 100.0 83.0 4 000
4 500 100.0 75.0 26 000 100.0 75.0 7 000
4 000 100.0 67.0 28 000 100.0 67.0 11 000
3 500 100.0 58.0 29 500 100.0 58.0 16 000
3 000 100.0 50.0 31 500 100.0 50.0 22 500
2 500 100.0 42.0 33 500 100.0 42.0 30 000
2 000 100.0 33.0 35 000 100.0 33.0 39 000
Note
f The runtime may be shorter than the estimation due to the inuence of characteristics of each light source, conditions of use, installation
environment, etc.
f The duration of use is referred to as the runtime when you use the projector successively. The duration of use is an estimated duration and
is not the warranty period.
f If the runtime exceeds 20 000 hours, replacement of the components inside the projector may be required. Consult your dealer for details.
Setting [BRIGHTNESS CONTROL SETUP]
Set the operation of the brightness control function.
The [BRIGHTNESS CONTROL SETUP] setting is synchronized with the [PROJECTOR SETUP] menu →
[BRIGHTNESS CONTROL] → [BRIGHTNESS CONTROL SETUP]. The most recent setting is reected in both
items.
1) Press as to select [OPERATION SETTING].