You can set the timer to come on at a certain time to wake you
up. This unit offers 3 optional play timers.
Preparation:
Turn the unit on and set the clock (➡ above).
Prepare the music source (disc, radio, iPod/iPhone or AUX)
and set the volume.
Press [CLOCK/TIMER] repeatedly to select play timer.
Within 5 seconds, press [e,r] to set the starting time.
Press [OK].
To set the finishing time, repeat step and .
To activate the timer
Press [z, PLAY] repeatedly to turn the selected play
timer on.
Press [^] to turn the unit off.
•
•
This is a 24-hour clock.
Press [CLOCK/TIMER] to select “CLOCK”.
Within 5 seconds, press [e,r] to set the time.
(Press and hold to change the time faster.)
Press [OK].
To display the clock, press [CLOCK/TIMER].
Reset the clock regularly to maintain accuracy.
•
•
Setting the clock
Play timer
Change the
settings
Repeat step to (➡ above).
Change the
source or volume
Press [z, PLAY] twice to clear zPLAY
indicator from the display.
Make changes to the source or
volume.
Perform step and (➡ above).
Check the
settings (When
the unit is on or
in standby mode)
Press [CLOCK/TIMER] repeatedly to
select “zPLAY 1”, “zPLAY 2” or
“zPLAY 3”.
Cancel
Press [z, PLAY] twice to clear the timer
indicator from the display.
The timer will start at the preset time, with the volume
increasing gradually to the preset level.
•
Timer
The sleep timer can turn the unit off after a set time.
Press [SLEEP] to turn the sleep function on or off.
Press [SLEEP] once to check the remaining time.
The play timer and sleep timer can be used together. The
sleep timer always has the priority. Be sure not to overlap the
timer settings.
When AUTO OFF is ON and the unit is left unused for about
30 minutes, the unit will shut down even if the play time or
sleep time has not expired.
•
•
Sleep timer
OFF (Cancelled)
Preset EQ Press [PRESET EQ] repeatedly to select
“HEAVY”, “SOFT”, “CLEAR”, “VOCAL” or
“FLAT”.
Bass or Treble
Press [BASS/TREBLE] repeatedly to
select “BASS” or “TREBLE”.
Press [e,r] to adjust the level
(-4 to +4).
Surround
Sound
Press [SURROUND] repeatedly during
play to select “ON SURROUND” or
“OFF SURROUND”.
If interference in FM stereo reception
increases, cancel the surround sound
effect.
D.Bass Press [D.BASS] repeatedly during play to
select “ON D.BASS” or “OFF D.BASS”.
Re-master
(MP3)
Press [RE-MASTER] repeatedly during
play to select “ON RE-MASTER” or
“OFF RE-MASTER”.
Sound adjustment
External unit
The remote control and main unit are factory-set to “REMOTE 1”
mode.
If you find the remote control unintentionally also controls other
equipment, you can switch to operate in “REMOTE 2” mode.
To switch to “REMOTE 2” mode (by main unit only)
Press [DAB/FM/AUX] to select ‘‘AUX’’.
Press and hold [DAB/FM/AUX] and then press [2] until
“REMOTE 2” is displayed.
Press and hold [OK] and [2] for at least 2 seconds.
To return to “REMOTE 1” mode
Repeat the steps above but replace [2] with [1].
(“REMOTE 1” will be displayed.)
Changing the main unit and remote control
mode
Plug the audio cord into the AUX jack.
Plug type: 3.5 mm stereo
Press [AUX] and start playback from the
portable audio source.
You can select the sound input level of the portable audio
equipment.
Press [PLAY MODE] repeatedly to select “HIGH” or
“NORMAL”.
Switch the equalizer off or turn the volume of the portable
equipment down to reduce the input signal. High level of input
signal will distort the sound.
For details, refer to the instruction manual of the other
equipment.
Cords and equipment are not included.
•
•
•
Portable audio equipment (during AUX mode)
To Next Page
Loading...
Need help?
General
