What to do if my Panasonic TH-50LFB70E has no picture?
If your Panasonic Monitor displays no picture, there might be a few reasons. First, ensure the monitor is plugged into an AC outlet. Then, check if the monitor is switched on by pressing the power switch or the stand-by button on the remote control. Finally, check the Picture and Brightness/Volume settings.
Why is there no sound on my Panasonic TH-50LFB70E?
If there is no sound on your Panasonic Monitor, check whether the mute function has been activated on the remote control by adjusting the volume.
What to do if the power of my Panasonic TH-50LFB70E automatically turns off?
If your Panasonic Monitor unexpectedly turns off, check the settings for “No signal power off”, “PC Power management”, “DVI-D Power management”, HDMI1 Power management, HDMI2 Power management and “No activity power off”. One of these settings may be enabled.
What to do if my Panasonic Monitor displays no picture or sound intermittently?
If your Panasonic Monitor sometimes shows no picture or sound when using HDMI or DVI signals through a selector or distributor, try turning the power off and on again. If that doesn't work, consider replacing the selector or distributor.
Why are multi-touch operations not working on my Panasonic TH-50LFB70E?
If multi-touch operations are not working on your Panasonic Monitor, it might be because the touch panel, which uses infrared rays, is being affected by light sources. First, check if the “Setup” - “Touch Screen Settings” is set to “On”. Then, move any light sources as far away from the touch panel as possible.
What to do if the RS-232C is uncontrollable on my Panasonic Monitor?
If the RS-232C is uncontrollable on your Panasonic Monitor, first check that the connection has been made properly. When controlling the RS-232C command from the RS-232C terminal in the display, make sure that “Control I/F Select” is “RS-232C”, and that “Control I/F Select” is “RS-232C(DIGITAL LlNK)”, and “DIGITAL LINK mode” is “DIGITAL LlNK(RS-232C)” when controlling from the RS-232C terminal of the DIGITAL LINK device.
What to do if the LAN is uncontrollable on my Panasonic Monitor?
If the LAN is uncontrollable on your Panasonic Monitor, check whether the connection has been made properly. Also, verify that “Control I/F Select” is set to “DIGITAL LINK/LAN” when controlling with the WEB browser control or the command control.
What to do if there is no picture or sound from the DIGITAL LINK terminal on my Panasonic TH-50LFB70E Monitor?
If there is no picture or sound output from the DIGITAL LINK terminal of your Panasonic Monitor, verify that the connection between the video (output) equipment and the twisted pair cable transmitter, and between the twisted pair cable transmitter and the monitor, is properly established.
Why does sending e-mail fail from my Panasonic TH-50LFB70E?
If sending e-mail fails from your Panasonic Monitor, verify that the e-mail settings in the Web browser are correct.
What does it mean when the power indicator is blinking red on my Panasonic Monitor?
If the power indicator on your Panasonic Monitor is blinking red, there is a possibility of malfunction.
General| Screen Size | 50 inches |
|---|---|
| Resolution | 1920 x 1080 pixels |
| Panel Type | IPS |
| Brightness | 350 cd/m² |
| Viewing Angle (Horizontal/Vertical) | 178°/178° |
| VESA Mounting | 400 x 400 mm |
| Aspect Ratio | 16:9 |
| Input Terminals | HDMI, DVI-D, VGA, Component, Composite |
| Output Terminals | Audio out |
| Speaker | 2 x 10W |
| Operating Hours | 16 hours/day |
To Next Page