What does Outdoor Air Temperature Sensor Abnormality (F36) mean for my Panasonic WH-SHF12F6E5 Heat Pump?
An Outdoor Air Temperature Sensor Abnormality (F36) in your Panasonic Heat Pump can be caused by: * Faulty connector connection. * Faulty sensor. * Faulty outdoor unit PCB (main). Continue for 5 seconds.
What causes a Compressor Low Pressure Protection (H42) error in my Panasonic Heat Pump?
A Compressor Low Pressure Protection (H42) error in your Panasonic Heat Pump can be triggered by: * Dust accumulation on the outdoor unit heat exchanger. * Air short circuit at the outdoor unit. * A partially closed 3-way valve. * A faulty outdoor unit fan motor. * Refrigerant shortage (refrigerant leakage). * A clogged expansion valve or strainer. * A faulty outdoor pipe temperature sensor. * A faulty outdoor unit main PCB (main).
What does Outdoor High Pressure Abnormality (H64) mean for my Panasonic Heat Pump?
If your Panasonic Heat Pump displays an Outdoor High Pressure Abnormality (H64), it could be due to: * A faulty connector connection. * A faulty sensor. * A faulty outdoor unit PCB (main). In this case, continue 4 times in 20 minutes.
Why does my Panasonic WH-SHF12F6E5 display Indoor/Outdoor Abnormal Communication (H90)?
The Panasonic Heat Pump may display an Indoor/Outdoor Abnormal Communication (H90) error if there is: * A faulty outdoor unit PCB (main). * A faulty indoor unit PCB (main). * An indoor-outdoor signal transmission error due to wrong wiring. * An indoor-outdoor signal transmission error due to breaking of wire in the connection wires between the indoor and outdoor units. * An indoor-outdoor signal transmission error due to disturbed power supply waveform. Continue for 1 minute after operation.
What does Indoor Water Inlet Temperature Sensor Abnormality (F37) mean on my Panasonic WH-SHF12F6E5 Heat Pump?
An Indoor Water Inlet Temperature Sensor Abnormality (F37) in your Panasonic Heat Pump could be due to: * Faulty connector connection. * Faulty sensor. * Faulty indoor unit PCB (main). Continue for 5 seconds.
What does Outdoor Current Transformer Open Circuit (F46) mean for my Panasonic Heat Pump?
An Outdoor Current Transformer Open Circuit (F46) in your Panasonic Heat Pump may indicate: * CT defective. * Faulty outdoor unit PCB. * Compressor defective (low compression). Continue 3 times in 20 seconds.
What does Deice Circulation Error (H65) mean on my Panasonic Heat Pump?
A Deice Circulation Error (H65) on your Panasonic Heat Pump could indicate: * Water flow in air-to-water heatpump indoor unit circuitry. * Faulty indoor unit water flow switch. * Faulty indoor unit water pump. * Faulty indoor unit PCB. Continue for 10 seconds.
What does Water Pump Abnormality (H20) mean for my Panasonic WH-SHF12F6E5 Heat Pump?
A Water Pump Abnormality (H20) in your Panasonic Heat Pump may be due to: * Operation stop due to short circuit inside the water pump motor winding. * Operation stop due to breaking of wire inside the water pump motor. * Operation stop due to breaking of water pump lead wires. * Operation stop due to water pump motor IPM malfunction. * Operation error due to faulty indoor unit PCB. Continue for 5 seconds.
What does Outdoor High Pressure Switch Activate (F12) mean for my Panasonic WH-SHF12F6E5 Heat Pump?
If your Panasonic Heat Pump displays Outdoor High Pressure Switch Activate (F12), it could be caused by: * Faulty water pump. * Insufficient water flow rate in system. * Water leak in system. * 3 way valve closed. * Clogged expansion valve or strainer. * Excessive refrigerant. * Faulty outdoor high pressure sensor and switch. * Faulty outdoor unit PCB. Continue 4 times in 20 minutes.
What causes a Four Way Valve Abnormality (F25) in my Panasonic WH-SHF12F6E5 Heat Pump?
A Four Way Valve Abnormality (F25) in your Panasonic Heat Pump can be caused by: * A faulty sensor. * A faulty connector connection. * A faulty outdoor unit PCB (noise filter/main). * A faulty four-way valve. Continue 4 times in 30 minutes.
Explains symbols for warnings, cautions, and prohibited actions.
Detailed technical specifications for the WH-SHF09F3E5 and WH-UH09FE5 models.
Detailed technical specifications for the WH-SHF12F6E5 and WH-UH12FE5 models.
Identifies controls and components of the indoor unit, including the control panel.
Shows the physical layout and air flow paths of the outdoor unit.
Guidelines for choosing optimal indoor and outdoor unit placement.
Steps for installing the indoor unit, including plates, piping, and wiring.
Steps for installing the outdoor unit, including piping, wiring, and drain water disposal.
Explains basic functions, heating modes, and thermostat controls.
Details water pump operation, speed adjustment, and error handling.
Covers safety, auto restart, indications, back-up heater, tank, sterilization, quiet, anti-freeze, solar.
Outlines safety mechanisms for compressor operation and overall system protection.
Details protection measures specific to heating operation, including deice.
Instructions on how to safely remove front plates, cabinets, and other components.
Steps for performing a test run and proper pump down operation for servicing.
How to diagnose issues related to the refrigeration cycle and pressure.
Explains error codes and the breakdown self-diagnosis function.
Detailed troubleshooting steps for common error codes and malfunctions.
Step-by-step guide to remove parts like pressure gauges, control panels, and RCCBs.
Instructions for removing electronic boards, transformers, valves, and pumps.
Performance data including capacity and input power at various conditions.
Tables showing heating capacity and input power based on air and water temperatures.
Visual breakdown of components and their corresponding part numbers.
Visual breakdown of components and their corresponding part numbers.
To Next Page
General