Parker PV028 Installation And Start-Up Information

16 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Visit our homepage for additional support

parker.com/pmde

Effective: December 20, 2018

Supersedes: July 1, 2010

Bulletin MSG30-3245-INST/UK

Installation and

start-up information

PV series

Design series ≥ 44, PVplus

Variable displacement

axial piston pump

Table of Contents

Other manuals for Parker PV028

Installation And Setup Manual28 pages

Questions and Answers:

M
Michael SmithAug 22, 2025
What to do if my Parker PV028 Water Pump drive motor does not turn?
- K
  knappanthonyAug 22, 2025
  If the drive motor of your Parker Water Pump isn't turning, it could be due to a few reasons. First, check the motor connections and the electrical power supply to ensure they are correctly connected and functioning. It's possible that one of the three phases has failed. If the motor connections and power supply are fine, the pump may be mechanically blocked, in which case you should send the pump to the factory for service.
M
Matthew ElliottAug 25, 2025
Why Parker PV028 drive motor turns, but pump does not turn?
- M
  Monica BrownAug 25, 2025
  If the drive motor of your Parker Water Pump is turning but the pump itself isn't, the coupling might not be mounted correctly. Check the coupling assembly and correct it.
A
Alyssa MooneyAug 26, 2025
What to do if Parker PV028 drive motor turns and pump turns, but there is no output?
- J
  juliaphelpsAug 26, 2025
  If the drive motor and pump of your Parker Water Pump are both turning, but there's no output, consider these possibilities: Ensure the direction of motor rotation is correct by changing it if necessary. Check that the fluid reservoir is filled to the required level and increase the suction pipe length if needed. Inspect the suction line for blockages and open any valves in the line, ensuring they have electrical indicators. Also, check the suction filter. Seal the suction line to prevent air from entering. Unload the pressure port and system before starting, and bleed air from the pressure line if the pressure line/system cannot bleed air out.
S
stacymanningAug 28, 2025
How to fix unstable compensator on Parker Water Pump?
- J
  Jennifer SkinnerAug 28, 2025
  To address an unstable compensator in your Parker Water Pump, consider these steps: First, clean the hydraulic system and compensator valve, as the compensator spool might be sticking due to hydraulic fluid contamination. Next, adjust the compensator differential pressure to the required setting, as it may have changed (becoming too low or too high). Ensure the correct pilot orifice and pressure pilot valve are selected as recommended. If dealing with a dynamic critical system, such as a pressure compensator combined with a pressure reducing valve, use a remote pressure compensator instead of a standard one, and install an orifice in the load sensing line remote from the compensator, as close as possible to the load sensing valve.
E
esanchezAug 30, 2025
What to do if Parker Water Pump does not compensate?
- J
  jeffrey17Aug 30, 2025
  If your Parker Water Pump isn't compensating, check these potential issues: Ensure there is an orifice Ø 0.8 mm in the load sensing line to compensator code MFC. Verify that a pressure pilot valve is connected to the compensator and that the valve opens as required. Confirm that the load sensing line is connected downstream (actuator side) of the load sensing valve. Also, ensure that the pump outlet pressure is at least 15 bar, as the bias spring in the pump cannot be compressed otherwise.
M
melissa43Aug 31, 2025
Why Parker PV028 Water Pump drive motor only turns at slow speed?
- T
  Tyler MurphySep 1, 2025
  If the drive motor of your Parker Water Pump only turns at slow speed, it could be due to improper motor selection or a hydraulically blocked pump. Start the pump at an unloaded system and consider using a motor with more horsepower. Also, check the function of the pump compensator and start the pump at an unloaded system.
A
Anthony TranSep 3, 2025
What to do if Parker PV028 Water Pump does not upstroke?
- T
  Troy MarshSep 3, 2025
  If your Parker Water Pump does not upstroke and sticks at zero displacement, it could be due to a blocked compensator or an interrupted cable. Clean the hydraulic fluid and compensator valve, as the compensator might be blocked due to contamination. Check the wiring to the LVDT or proportional solenoid to ensure the cable is intact; replace it if necessary.

Parker PV028 Specifications

General

Displacement	28 cc/rev
Mounting	SAE A 2-Bolt
Speed (Maximum)	3000 RPM
Flow Rate	84 l/min
Rotation	Clockwise/Counter-clockwise

Related product manuals

Preview: Parker P2 Series

Parker P2 Series

Preview: Parker P1/PD Series

Parker P1/PD Series

Preview: Parker PGP 600 Series

Parker PGP 600 Series

Preview: Parker 47 Series

Parker 47 Series

Preview: Parker Series V14

Parker Series V14

Preview: Parker AFL Series

Parker AFL Series