To Next PageTo Next PageWhy is my Parkside PBS 350 A1 motor making excessive noise?
If the motor of your Parkside Saw is making excessive noise, the coils may be damaged, or the motor may be defective. Arrange for a specialist to inspect the motor.
How to fix a rough or wavy saw cut with my Parkside PBS 350 A1 Saw?
If your Parkside Saw's cut is rough or wavy, the saw blade may be dull, or the tooth shape might not be appropriate for the material thickness. Try resharpening the saw blade and/or using a more suitable saw blade.
Why doesn't my Parkside PBS 350 A1 motor reach its full power?
If the motor of your Parkside Saw does not reach its full power, it's possible that the circuits in the network are overloaded by other equipment. Avoid using any other equipment or motors on the same circuit.
What to do if burn marks appear on the wood when cutting with my Parkside Saw?
If burn marks appear on the wood during cutting with your Parkside Saw, it could be due to a blunt or wrong saw blade. Try changing the saw blade or selecting a saw blade according to the operating instructions.
What to do if the saw blade jams during cutting work with my Parkside PBS 350 A1?
If the saw blade of your Parkside Saw jams during cutting, it could be due to a blunt saw blade, deposits on the saw blade, or a poorly set guide. Try changing the saw blade, cleaning the saw blade, and setting the saw blade guide according to the operating instructions.
What to do if the saw blade jams during cutting with my Parkside PBS 350 A1 Saw?
If the saw blade of your Parkside Saw jams during cutting, it could be due to a blunt saw blade, deposits on the saw blade, or a poorly set guide. Here's what to do: 1. Change the saw blade. 2. Clean the saw blade. 3. Set the saw blade guide according to the operating instructions.
What to do if my Parkside PBS 350 A1 Saw motor does not work?
If the motor of your Parkside Saw isn't working, the motor, cable, or plug might be defective, the fuses might be burnt, or the housing cover might be open. Have a specialist inspect the machine. Never attempt to repair the motor yourself due to the danger involved. Check the fuses and replace them if necessary. Ensure the housing cover is closed correctly.
Why does the motor on my Parkside PBS 350 A1 Saw overheat easily?
The motor of your Parkside Saw may overheat easily due to overloading or insufficient cooling. To resolve this, avoid overloading the motor while cutting and remove dust from the motor to ensure optimal cooling.
Why does my Parkside PBS 350 A1 Saw motor not reach full power?
If your Parkside Saw's motor is not reaching its full power, it might be due to overloaded circuits. Try not using other equipment or motors on the same circuit.
Why does the Parkside PBS 350 A1 Saw motor start slowly and not reach full speed?
If the motor of your Parkside Saw starts up slowly and does not reach operating speed, it could be due to voltage being too low, damaged coils, or a burnt capacitor. Contact the utility provider to check the voltage. Arrange for inspection of the motor by a specialist. Arrange for replacement of the capacitor by a specialist.
Lists all items included in the package with the band saw.
Describes the specific purpose and application for which the band saw is designed.
Guide for assembling the saw table onto the band saw machine.
Instructions on how to properly tension the saw band for optimal operation.
Guide on adjusting the saw band alignment on the rollers for accurate cuts.
Details on adjusting the top guide pins for precise saw band alignment.
Instructions for adjusting the bottom guide pins for correct saw band guidance.
How to adjust the height of the top saw band guide relative to the workpiece.
Guide to set the saw table to a precise 90-degree angle for square cuts.
Advice on choosing saw bands and steps for replacing them.
Information on replacing the table insert and using the extraction nozzle.
Instructions for turning the machine on and off using the main switch.
Guide on how to use the parallel stop for straight cuts.
How to perform angled cuts by tilting the saw table.
Instructions for performing cuts along the length of the workpiece.
How to perform angled cuts using the adjusted saw table.
Techniques for cutting curves and radii without a guide.
General