DESIGNED AND ENGINEERED IN U.S.A.
REFER ALL SERVICING TO PEAVEY
AUTHORIZED SERVICE CENTER
CAUTION
ALL TUBES 12AX7A
6505
EFFECTS PREAMP
A PRODUCT OF PEAVEY ELECTRONICS CORP.
5022 HARTLEY PEAVEY DRIVE
MERIDIAN MS. 39305, U.S.A.
SEND
BIAS
TEST
FUSE
100V
F8AL/250V
115V
F5AL/250V
220/240V
F3.15AL/250V
100-240V
50/60Hz
400 WATTS
Consumo de energia 400Wh
Consumo de energia
en modo de espera 71Wh
BIAS
VOLTAGE
GND
RETURN OUT REMOTE SWITCH Made in ChinaCLASS 2 WIRING
SPEAKER OUTPUTS
120W RMS/44V RMS 4Ω MIN.
SPEAKER JACKS PARALLELED
100V
100V
240V
240V
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
0
1
2
3
4
5
6
7
8
9
10
CHANNEL
BRIGHT
CRUNCH
SELECT
HIGHMIDLOWPRE
INPUT
POST HIGHMIDLOWPRE POST RESONANCE PRESENCE RESONANCE PRESENCE
POWER
ONON
STANDBY
RHYTHM RHYTHM LEADLEAD
(7) REMOTE FOOTSWITCH JACK
This jack is provided for the connection of the supplied remote footswitch. The footswitch cable
should be plugged in before the amp is powered up. When the footswitch is plugged into the Remote
Footswitch Jack, the Channel Select switch (14) must be pressed to the “in” position for remote
selection of the Lead or Rhythm channel (right footswitch button). The On and O operation of
Eects (left footswitch button) will work at all times. Remote selection of Crunch gain boost
(center footswitch button) is available only when the Crunch Switch (22) is selected. See page 9
for detailed Footswitch diagram.
(8) SPEAKER JACKS
These jacks are provided for the connection of speaker enclosure(s). The minimum speaker
impedance is 4 ohms. The Impedance Selector Switch (5) should be set accordingly.
(9) IMPEDANCE SELECTOR SWITCH (5)
Use this switch to select the appropriate impedance of the speaker enclosure(s) connected to
the Speaker Jacks (4). If two enclosures of equal impedance are used, the switch should be
set at one half of that value (e.g., two 16 ohm enclosures: set switch to 8 ohms; two 8 ohm
enclosures: set switch to 4 ohms).
Front Panel
12 13
14 16 18 11 10
15 17 18 19 20 21 22 23
(10) POWER SWITCH/LED
This switch supplies power to the unit. Depressed to the “ON” position, the red Power LED indicator
will illuminate above the Power Switch when power is being supplied to the unit.
(11) STANDBY SWITCH/LED
This switch allows the 6505 II to be placed in a non-operational standby mode. When the Standby
Switch is activated, the tubes remain hot and ready for instantaneous operation, eliminating
warm-up time. The Standby LED indicator above the switch will illuminate when the amp is in the
operational mode.
(12) INPUT
The 6505 II input jack is designed to accommodate a variety of guitar output levels, regardless of
pickup conguration. Due to the extreme high gain capabilities of the 6505 II, it is imperative
that you use a premium shielded instrument cable in order to minimize noise.
(13) CHANNEL SELECT SWITCH
This switch allows selection of the Rhythm or Lead Channel. Depressing the switch to the “in”
To Next Page
Loading...
