Peavey Studio Chorus 210 - Technical Specifications; Power Amp Section Specifications; Preamp Section Specifications; Output and Special Feature Specifications

SPECIFICATIONS
POWER AMP SECTION
Rated Power & Load: (Each
Channel)
45 W RMS into 8 ohms/driven
separately
35 W RMS into 8 ohms/both
channels driven
(70 W RMS Total)
Power @ Clipping:
(Typically each channel)
(50/o THD, 1 kHz, 120 V AC line)
40 W RMS into 8 ohms/both
channels driven
Frequency Response:
+0, -2 dB, 40 Hz to 15 kHz
@ 30 W RMS into 8 ohms
Total Harmonic Distortion:
Less than 0.2%, 100 mW to
30 W RMS, 40 Hz to 15 kHz,
8 ohms (Typically below 0.1%)
Hum & Noise:
Greater than 75 dB below rated
power
Power Consumption:
(Domestic)
200 watts @ 120 V AC,
50/60 Hz
PREAMP SECTION
The following specs are measured @
1 kHz with the controls preset as follows:
Push Bright Off (Out)
Channel Select Normal (Out)
Low & High EQ @ 10
Mid EQ @ 0
Presence EQ @ 0 dB
Supersat® @ 10
Post Gain @ 10
Gain & Shift Switches off (Out)
Bottom, Body, & Edge voicing
@ 0 dB
Reverb Level @ 0
Stereo Chorus Depth & Rate
@ 0
Nominal levels are with normal
gain @ 5.
Minimum levels are with normal
gain @ 10.
Preamp High Gain Input:
(Normal Channel)
Impedance: High Z, 220 K ohms
Nominal Input Level: -16 dBV,
150 mV RMS
Minimum Input Level: -34 dBV,
20 mV RMS
Maximum Input Level:
+ 16 dBV, 6 V RMS
Preamp Low Gain Input:
(Normal Channel)
Impedance: High Z, 44 K ohms
Nominal Input Level: -10 dBV,
300 mV RMS
Minimum Input Level: -40 dBV,
10 mV RMS
Maximum Input Level:
+22 dBV, 12 V RMS
Preamp High Gain Input:
(Lead Channel)
Impedance: High Z, 220K ohms
Nominal Input Level: -46 dBV,
5 mV RMS
Minimum Input Level: -60 dBV,
1 mV RMS
Preamp #1 Output:
(Dry Signal, No Chorus)
Load Impedance: 10 K ohms or
greater
Nominal Output: 0 dBV,
1 V RMS
Maximum Output: +18 dBV,
8 V RMS
(Switching jack, removes dry
signal feed to output #2 when
used, allowing full stereo output
patching)
Preamp #2 Output: (Mix Of
Dry And Chorus Signals)
Load Impedance: 10 K ohms or
greater
Nominal Output: 0 dBV,
1 V RMS
Maximum Output: +18 dBV,
8 V RMS (This output is con¬
verted to chorus signal only if
output #1 above is used for out¬
put patching)
Power Amp #1 & #2 Inputs:
Impedance: High Z, 33 K ohms
Designed Input Level: 0 dBV,
1 V RMS (Switching jacks pro¬
viding the preamp output to
power amp input connections
when not used)
Headphone Output:
(Stereo Jack, Stereo Signal)
Load Impedance: 4 ohms or
greater/channel
Nominal Power Output: 100 mW
into 4 ohms/channel
(Switching jack, disconnects in¬
ternal speakers when a stereo
phone plug is fully inserted)
System Hum & Noise @
Nominal Input Levels:
(20 Hz to 20 kHz unweighted)
70 dB below rated power
Normal Channel Equalization:
Low, Mid, & High Passive Type
EQ
Automatic thick EQ when lead
channel selected
Presence: ±15 dB @ 5 kHz
Push Bright: +6 dB @ 2 kHz
Lead Channel Voicing:
Special Bottom, Body, & Edge
active type EQ
Push Shift: Shifts frequency of
Body effect
Push Gain: Increases SuperSat®
gain +20 dB
External Footswitch Function:
Reverb Defeat (When reverb con¬
trol raised)
Lead Channel Defeat (When
selected with button)
Chorus Defeat (When chorus
depth raised)